DX4500EA3WW General Electric Dryer - Instructions

I narrowed the porblem down to the rotary start switch, which is located in the top panel. It takes a hex wrench to remove the four screws holding the fron top panel in place and of course the knobs had to be removed. The switch rotates about a wuarter of a turn to come out. Label and remove the three connectors (3). It took about a week to get the replacement part which was slightly different than the original part. The good thing is it had the three prongs like the old part.. I hooked the connectors in the same configuration as the old switch, plugged the power cord back in to test and it started right up.

Unscrewed three screws on back and removed the switch and inserted the new one. There are 3 wires that clamp on the switch. Remember to unplug before doing this.

Real easy and great people to work with. Much cheaper than a technician repair.

Jim

Pulled off old knob put on new one

Took out four screws on the upper panel and removed. Turn the control in the inner panel allowing it to seperate from the inner panel. Changed each wire at at time from the old control to the new one. Reassembled unit and tested it. All worked well.

Unplug. Remove 3 knobs at front of panel. Remove 4 screws. Panel pulls forward. Remove green grounding wire to allow panel to come forward more. Pry up locking tab on switch. Turn switch to unlock from panel. Install new switch in reverse order of removal. Pull off each wire one at a time from old switch and attach to new switch. Reinstall panel and insert 4 screws. Done. My wife was so suprised that it actually worked and I fixed it in less than a day! Only took about 20 minutes. Thanks Part Select and the other repair stories that I read on your website.

I moved the dryer away from the wall and unplugged the electrical cord. I unscrewed the 4 screws on the top of the dryer to gain access to the Dryer Rotary Start Switch. I pulled the part out of its set location and carefully removed the clip on wires. I then carefully attached the wires to the exact locations on the new part and put it back into the proper location. I installed the screws, plugged in the power cord and moved the dryer back to its location for operation. I turned the circuit breaker back on. I failed to mention that I turned that off first of all. I set the dryer control to dry and turned the Dryer Rotary Start Switch to on and it worked immediately. This took about 12 minutes totally from start to finish.
Thank you for being there.
Sincerely, John Pewters

Searched dryer model on Google, found partselect.com. Searched for Dryer model and a diagram of the dryer with all its parts appeared. Selected the timer knob on the diagram and it took me to the part, ordered it.
All steps took less than 10 minutes, and I had the new knob in my hands the next day and installed in about 3 minutes.
You saved a few dollars, plus not having to miss time from work waiting for a repair man.
Thank you!
Rocio

Removed the 6 screws that held the top panel in place. there are only 3 wires, 2 that go together and 1 single wire.Uplug the dryer,twist out the old switch,twist in the new one, attatch the wires,replace the panel,BAM your done.And the best part of it all the part was right the first time.they make it so easy to get the right part the first time!

First unplug dryer to prevent electrical shock. To remove the front of the dryer, open the door in top left and top right corners is a machine screw. They can be removed with a Phillips screw driver. Lift the top slightly and let front fall forward about 6 inches, lift slightly. Two wire will be connected to the switch in the door. remove the wires and squeeze the tabs on both sides of the switch and push it out. Push new switch in to replace old switch and reassemble.

I first unplugged the unit, opened the top, disconnected and took off the control panel, took off the front panel to determine the source of the squeaking noise coming from the Dryer. I saw that 3 of the 4 Front Drum Glides were gone and the drum had worn away significant amounts of plastic from the Top Bearing Assembly. I purchased the Top Bearing Assembly and a set of 4 Front Drum Glides. Disassembled the damaged parts and reassembled with the new replacement parts. The reassembly took less than 20 minutes. I plugged in the Dryer and viola! It works as good as new.

opened up the control cover, pulled off the 3 wires to the switch. unclipped the swutch from the panel and reinstalled the new exact replacemnt sww you sent

Pulled the unit all apart to replace the rear drum bearing. Also replaced the front bearing. Works like brand new. Easier then I thought

Dryer is 3 yeras old. This dryer switch / start knob broke three times. First two GE repair fixed it. Charge was about $75 to $100. Then I found Parts Select, Who what great prices. Switch cost under $10. and took me 10 minutes to install. Dryer works great again. OH, I ordered an extra switch to have on hand.

Simply replaced it. I have ordered from Parts Select several times. Excellent customer service. They always have the parts that I need and ship them to me promptly. Great company!

Took off old timer and put new knob on and it fit.