DBR453EA1WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- La Rae from Buda, TX
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob broke inside
Replacement knob went on without tools in 1 second.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlene from Winchester, KY
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Knob came off
I'm not experience to repair anything so I put the laptop on top of the washer and watch the video and it was easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Stockton, CA
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken timer knob
Knob fit perfect. Simple pull off and put new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENDALL from COCOA, FL
- Parts Used:
- WE4X881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Inoperative Switch
Remove & rplace switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne from Marblehead, MA
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The time knob had broken and come off
Our repair was super easy. All we had to do was line the new Timer Knob up with the knob on the dryer and slip it on. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Orange, CA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken knob
Simple replacement. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Ennis, MT
- Parts Used:
- WE4X881
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Dryer start switch broken off
Put in the new switch and it starts great. Now that it runs there is no heat. I assume the elements are out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from San Marcos, CA
- Parts Used:
- 5303937183
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
noise
i folow the instructions from web page
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Edna, TX
- Parts Used:
- WE12X10009
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Drum would not turn at full speed, noisy squeak
Top control panel removed; next used screwdriver to lift up dryer top on each side( the top of dryer is attached by clips on the underside) the dryer front panel has two screws, one on each side of inside front(they are easy to reach and near the top of the inside front panel, after removing these two screws we used screwdriver again to pry off front panel as it is attached also by clips on inside of front panel. At this point there is easy access to the drum where the old belt was removed, new belt put in place; removed small panel on back of dryer to access idler pulley and attached new belt through the pulley; turned the drum a couple of times by hand to check if belt was running true on the drum; problem fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Yorktown, IN
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broke the knob.
I used a pair of pliers to turn my dryer on until I broke the center part where the knob went. I order the part that was in the dryer first and it came the next day. When it got here I realized I still needed the knob. It came the next day also. It took my handyman about 15 minutes to replace both and he also cleaned out all of the missing socks and other items behind my dryer. Good Job!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June from Port Charlotte, FL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Start knob broke
It was only a matter of putting a new knob in place of the broken one. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Bakersfield, CA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Dryer Start knob broken inside of stem.
Knob stem was split, leaving the metal bushing on the dryer's Start switch. Used pliers to remove metal collet. Aligned new knob to switch, and firmly pushed replacement part into place. Tested results and found it to be satisfactory.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Sun City West, AZ
- Parts Used:
- WE4X881
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Sticker Switch Worn Out
Simple replaced switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Staten Island, NY
- Parts Used:
- WE12X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
the dryer belt broke
very simple my husband put it on in no time
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dee from San Saba, TX
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer would not turn on
took the old part off @ put the new one on. Took about 5 sec.
Was this instruction helpful to you?
Thank you for voting!