DBB3300EA1WW General Electric Dryer - Instructions

We removed the top of the the dryer and then removed the front part. Then put the traps in place, put the other parts of the dryer back on, and turned the dryer back on. Just as simple as that. No extra fees.

Took the top of the dryer off by removing two philips screws in front. Removed two screws holding the front of the dryer on. Pulled the front out enough to reveal the worn drum slides. Replaced them. Reassembled.

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.

When the part came in the mail. I opened the packaging & just pushed the knob on to the metal post of the dryer. Voile that easy!

First I removed the 2 screws that hold the lid down. Then I pulled the lid off. Then I removed the 2 screws that hold the front of the dryer in place. Then I lifted the drum a little and pulled the front cabinet out a little so I could see the drum slides. I removed the bad drum slides and installed the new ones. I then put everything back together and turned on the dryer. The squeeky noise was gone.

The repair was extremely easy. Just pulled the broken knob off and replaced with the new one. No tools required.

Before ordering from PartSelect I had checked both the original vendor and a local repair shop. The vendor had nothing, said try online. The shop said they could order it for twice the price.

PartSelect sent exactly what I needed pronto. I pulled off the old knob. I pressed on the new knob.
Done.

The repair was pull old one off and replace new knob. Receiving the new knob was amazing. Ordered one afternoon and received new part by 11 am next morning at regular shipping. You can't ask for anything better than that. Thank you

Silmply replaced the knob. This is the second knob I have replaced on this dryer. This time I bought two for when it happens again. Not sure if it is too much rension in the timer or too little strength in the knob, but is a design problem.

The fact that the knob on a 3yr old dryer broke was harder to deal with than the repair. It was lift the old knob off (it was very loose) and snugly slide the new knob on. I can get back to reading my book and my wife thinks I'm a hero win-win!

I ordered to timer knob. Its was delievered in two days. When I received it, My bother and I looked at it expecting more than what we received, We said to each other this isn't going to work. I told my bother to go on and try it anyway. He took the old timer knob off and then removed a clamp at the base of the timer knob fitting. He then placed the timer knob back of the fitting. Turned the dryer on and it started right up. We were both shocked that it ran and that it was so easy to fix. Thank you PartSelect. Great customer service. I have already ordered a part for his refrigerator! Can't wait till we get the part. I'm sure its going to work just fine.

My husband snapped the new know easily into place.

I was tired of the process after having the know break three times in less than three years which makes me think there is a design flaw.

I simply removed the switch and matched the pole numbers to the new switch eventhough the new switch had two extra poles. The switch replacement was straightforward and worked very well.

1st I suspected it's just the timer knob so I ordered the knob. Soon as I was installing the knob it was too loose, when I inspected the timer stem it was also broke. So I ordered a timer. Soon as the timer arrived, I installed the timer and tested the dryer then it came on.

1) Disconnect power supply. 2) Open dryer door to find and remove two screws through dryer top. 3) Proceed to lift front dryer top panel and tap rear of dryer top with hand to left to disengage tabs and remove dryer top completely. 4) Remove two screws through front panel. 5) Gently lift dryer front panel from base tabs to partial remove panel (careful of wires which remain connected) - pivot front panel to left with wires connected. 6) lift dryer barrel with left hand / reach under barrel with right hand to release belt from tensioner pulley (very easy one-hand maneuver). pull dryer barrel belt off tensioner pulley towards you, remove belt from motor pulley below. 7) lift/pull and remove dryer barrel and belt (flex side panels). 8) take picture of wire connection locations on heating element and remove wires from tabs two locations / 3 wires. 9) remove sensors 3 locations. 10) remove heating element and housing. 11) install new heating element / housing and reverse process. .....tip; belt tensioner pulley was biggest challenge at first because it was hard to see how it all worked and reach. once i realized i could force / lift the barrel up to gain better access it was much easier than trying to fit my arm through the one large available hole at bottom right (when looking at the unit). the tensioner pulley is opposite side (left when facing) and you would have to reach over the exhaust, etc.