DWXR483EB2CC General Electric Dryer - Instructions

removed three screws from face panel and removed three wires from starter switch and put them on new starter switch. Took old switch out and put in new and reassembled the face plate.

I pulled all the knobs, removed screws and tilted the faceplate, unplugged 3 wires, twisted the old switch to unlock it, twisted the new switch in and guessed where to install the 3 wires because the switch from PartSelect was different. After two attempts at placing the wires on the connectors, the dryer works however it shuts off at a different switch position.

Ordered and replaced the starter switch. Ordering was easy, just entered the model # and got a diagram of the dryer, selected the started switch and place the order. The switch arrived a few days later. It was the right switch and installation was easy. Dryer is working fine.

The biggest challenge was figuring out how to remove the defective starter switch. By searching the internet I found someone describing the same problem and that you had to turn in counter-clockwise to remove it.

Hello,

I just want to start by saying thanks to Partselect for having such a great website. The site is easy to navigate and with the explosion views allowed 'us novice' to select the right part the first time.

With post from previous DIY'ers, help make my repair very easy and simple. I had to replace the timer and the Pulley Idler. I first removed the top, leaving the timer panel connected by wires. I then removed the belt from the drum. That step was easy since the Pulley Idler was broke. I simply slid off the drum with ease. Once the belt was off I disassembled the front panel of the dryer. With the front panel off, I used a 3ft clamp to hold the drum in place while I unscrewed the three drum screws inside. I then pulled the drum out and set to the side. The tension pulley was simple to remove and reinstall. I reversed the steps above until the I got to the installation of the timer panel. With the new timer I put them side by side. I pulled one wire at a time and replaced to the new timer. Once all wires have been transferred, I then pulled the knob off the front. I used a small and medium flat head screwdriver, the small one to pry up the keeper flap and the medium to hold it. I was able to turn the timer and release it with ease. I then inserted the new timer and replaced the knob. I finished reinstalling the dryer and tested. Works great! This all took approximately an hour.

I was teaching my associate how to do this repair so I showed him how to take off the top of the dryer. Then I showed him how to replace the drum slides. I had him clean out the dryer since we had it apart, and I also showed him how to remove the drum and then reinstall it. This was a very easy repair, and he learned a lot that he otherwise would not have known. Thanks for getting the parts to me so quickly. Rob from Clarks Summit.

Took off the top and front of the dryer---really easy, just two screws for each. Put new drum slides (4) on the front/sides of the drum. Then things got a little bit more difficult. Removed the drum entirely, vaccuumed everything out and had to replace the rear bearings. My husband did this part so I can't tell you exactly how he did it. Not too difficult though. The written directions from here were hard to read---need to make a new copy from the original as it's so copied that it's all smudged. Anyway, once we got the new bearings on, we put everything back together. Dryer works like a charm, at a fraction of the cost it would have been to get someone out to do it. Thanks a bunch for the fast service!

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.

First I got the front bearing, found out I needed the slides too. It was binding at first, so I undid an earlier misadjustment I made (on the back drum mount). and it works!

Took the top of the dryer off by removing two philips screws in front. Removed two screws holding the front of the dryer on. Pulled the front out enough to reveal the worn drum slides. Replaced them. Reassembled.

r/r parts unit runs great

Your instructions were execellent
Problem is solve
Thank you

Initially purchased just the plastic slides, but when I opened the dryer I found the top drum bearing was smashed and the plastic was basically gone in a whole section, so I then ended up ordering the bearing as well. If you hear the loud squeaking, just buy the top drum bearing and the 4 slides (two white and two dark green). It is an easy repair and the squeaking sound is gone.

Repair was VERY easy - 4 screws total! Used google to find a video online that showed the steps.

remove move 2 screws holding top of dryer down.then remove two top screw holding front panel on so i could get to were my slide bearing where at poped them out and slide in new ones then put it all back together that was it

todd e line eaton ohio usa