DNCD450EG0WC General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JUDITH from FRUITA, CO
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My lint filter had a big hole in it. My dryer is 10+ years old.
All I had to do was remove the damaged filter and replace it with te new one. It could not ave been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRISTOPHER from PHENIX CITY, AL
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
I broke the door strike on the dryer.
Wife was out of town, visiting family. I broke the door strike by wedging the dryer door between the laundry room door, closed the laundry room door and it snapped the door strike breaking it. I ordered the part, and it shipped fast using the standard shipping, nothing fancy. Grabbed a pair of pliers and pushed the new door strike into place. It snapped right in, fits and works perfect like nothing ever happened. The wife will never know :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from HAWLEY, PA
- Parts Used:
- WE01X20419
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door handle broke
Snap off and then snap New one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- syd from wilmington, NC
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no handle
just replaced the unit handle and how my wife can open the dryer without a screwdriver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John C. from Cincinnati, OH
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door handle was comming off had broken hook
I pulled the old handle off and pushed the new one on.
No problem at all.
No problem at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from INMAN, SC
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old lint filter had deteriorated
Removed old one, inserted new one in slot. Just have to be sure it's turned in the right direction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- victor from ST AUGUSTINE, FL
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
door filter
was no repair- removed filter from door and installed new filter into door. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from DOVER, AR
- Parts Used:
- WE01X20419
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken dryer door handle
removed remaining handle pieces and simply snapped the new part in place. very simple,very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelly from MURFREESBORO, TN
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Squeaky dryer
I followed the YouTube video and it gave me step by step instructions however I really needed to replace my dryer slides to fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Salem, MA
- Parts Used:
- WE03X29897, WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
Rear drum bearing gone (only 4 years old). Decided to replace belt while I was at it.
I first watched the video on how to. Being mechecanically inclined I dismantled and removed everything needed to replace the drum bearing. Also removed belt at the same time. I replaced the bearing, then the belt. The belt could be a little tricky for some people. Getting the belt on the tension pulley could be a problem. What I did was I got a large nylon tie and put it around the armature of the motor. I then retracted the pulley just enough to be able to slip the belt over it. Of course this is all performed through the limited space on the bottom left, between the drum and the dryer shell. Once on the pulley, I cut the tie with wire cutters and it snapped into place. Rotated the drum a couple of times to line the belt with the pulley, perfect. I then put everything back together. I also cleaned any and all the lint that had gathered throughout the exhaust. Pluged the dryer in, perfect. Just like new. One more note getting the parts was so easy also. Your website and how to demo was a great help. Thank you, thank you very much. The words of the late Elvis Presley. They never get old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Naples, FL
- Parts Used:
- WE11M23
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Low heat
I bought the Heating Element and Housing together so that I would not have to stretch and run the coils and to save time!
1. I removed the two screws that hold the top down by opening the dryer door and removing the two screws at the top of the door opening. Then I pulled the top off.
2. Then I removed the two screws on the top inside of the dryer on the left right and took the front off.
3. Next I spread the dryer open a little and pulled the drum out while pushing the belt off the back of the drum.
4. Then I removed the screws to the sensors and removed them from the housing.
5. Then I removed the four screws holding the heating element housing to the back of the dryer and took it out and put in the new peace.
6. Do everything in reverse when putting the dryer back together.
1. I removed the two screws that hold the top down by opening the dryer door and removing the two screws at the top of the door opening. Then I pulled the top off.
2. Then I removed the two screws on the top inside of the dryer on the left right and took the front off.
3. Next I spread the dryer open a little and pulled the drum out while pushing the belt off the back of the drum.
4. Then I removed the screws to the sensors and removed them from the housing.
5. Then I removed the four screws holding the heating element housing to the back of the dryer and took it out and put in the new peace.
6. Do everything in reverse when putting the dryer back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from EPHRATA, PA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
Dryer needed a new dryer belt
I followed the directions I found on my tablet on youtube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Freeland, MI
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
loud noise when ran for 5 min.
Replaced the rear drum bearing. Not doing it before ,it took about 1 1/2 hrs. Problem was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Laurel Springs, NJ
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
dryer belt snapped
Replaced it as one would. I took off the front facing and replaced the belt. It took a bit of searching to find the proper way to route the belt around the pulley.
It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.
If I were to do it again, it would take 30 minutes or less.
It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.
If I were to do it again, it would take 30 minutes or less.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Forrest from Mays Landing, NJ
- Parts Used:
- WE14X25080
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Cracked air duct
Two screws under the dryer door then the top comes off.Then two screws hold the front on come out. 4 screws top is off and front is off the rest is no problem.
Was this instruction helpful to you?
Thank you for voting!