DWXR483EA0WW General Electric Dryer - Instructions

We removed the top of the the dryer and then removed the front part. Then put the traps in place, put the other parts of the dryer back on, and turned the dryer back on. Just as simple as that. No extra fees.

snap in snap out

Initially purchased just the plastic slides, but when I opened the dryer I found the top drum bearing was smashed and the plastic was basically gone in a whole section, so I then ended up ordering the bearing as well. If you hear the loud squeaking, just buy the top drum bearing and the 4 slides (two white and two dark green). It is an easy repair and the squeaking sound is gone.

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.

The knob had broken off a few months ago. I didn't think to look for one on the internet. I finally googled the brand name and part number and your company came up. It had the picture of the part which I ordered immediately. It came in the mail really quickly. I was so excited when I received the knob. I took it out of the package and slipped it over the stem in less than a minute. It went on perfectly. Now I no longer need to use pliers to turn on the dryer. It looks great and I am no longer inconvenienced. I love the new knob and would do business with this company again.

I thought that the timer was broken but when I pulled the knob off, there was a slight crack in it so before I contemplated calling a service person, I ordered a new knob. Now it works just fine and turns with the usual 'clicks' that I wasn't hearing since it broke. For the $20 ( including S&H ) It was worth the try. Thanks for the website, very easy to use!

Took it out of the package. Slid in it in place, took less than two minutes.

I simply removed the switch and matched the pole numbers to the new switch eventhough the new switch had two extra poles. The switch replacement was straightforward and worked very well.

Followed the Part Select video instructions which made the repair really easy!! Thanks for a job well done! ALSO.. the drum wobble was not caused by worn slides and felt. There are three screws holding the drum axle flange. Two of them fell out leaving the drum to flop about as it rotated. So we scavenged some screws from elsewhere on the dryer and problem solved. Once again.. thanks to Part Select for great instructional videos and great customer service ordering parts.

Before removing the old part,took photo with my phone camera to document the color wires hook up. Screwed in the new part and hooked up the color coded wires using the photo as reference. I was surprised how easy it was. Thanks. Partselect gave me fast shipping, cheap price and great customer service.

I suspected and removed the timer to check it and found the timer knob had a crack in it and realized I did not know where it was pointing to. Checking the selector knob also showed a crack which prevented the dryer from starting.

Took the dryer apart in an adjacent unused bedroom. Saw that the element was bad. Ordered new part from Part Select and installed when it arrived. The whole situation went as smooth as could be.

1) Disconnect power supply. 2) Open dryer door to find and remove two screws through dryer top. 3) Proceed to lift front dryer top panel and tap rear of dryer top with hand to left to disengage tabs and remove dryer top completely. 4) Remove two screws through front panel. 5) Gently lift dryer front panel from base tabs to partial remove panel (careful of wires which remain connected) - pivot front panel to left with wires connected. 6) lift dryer barrel with left hand / reach under barrel with right hand to release belt from tensioner pulley (very easy one-hand maneuver). pull dryer barrel belt off tensioner pulley towards you, remove belt from motor pulley below. 7) lift/pull and remove dryer barrel and belt (flex side panels). 8) take picture of wire connection locations on heating element and remove wires from tabs two locations / 3 wires. 9) remove sensors 3 locations. 10) remove heating element and housing. 11) install new heating element / housing and reverse process. .....tip; belt tensioner pulley was biggest challenge at first because it was hard to see how it all worked and reach. once i realized i could force / lift the barrel up to gain better access it was much easier than trying to fit my arm through the one large available hole at bottom right (when looking at the unit). the tensioner pulley is opposite side (left when facing) and you would have to reach over the exhaust, etc.

I used a pair of pliers to turn my dryer on until I broke the center part where the knob went. I order the part that was in the dryer first and it came the next day. When it got here I realized I still needed the knob. It came the next day also. It took my handyman about 15 minutes to replace both and he also cleaned out all of the missing socks and other items behind my dryer. Good Job!

Replaced drum bearing part and white slides.The problem was that it was not the drum slide support. It appears to be the the drum rear bearing of whch I am now ordering. The bearing replacement is a little more difficult, but I have taken this on as a challenge