DPSR405EA0WW General Electric Dryer - Instructions

pulled off the top, pulled off the front then replaced the plastic that was supporting the front side of the drum. fairly easy to replace although the little plastic 'slides' (you need 4 of them)

Repair was VERY easy - 4 screws total! Used google to find a video online that showed the steps.

r/r parts unit runs great

snap in snap out

We removed the top of the the dryer and then removed the front part. Then put the traps in place, put the other parts of the dryer back on, and turned the dryer back on. Just as simple as that. No extra fees.

i first popped off the top of te dryer after removing the two screws in frotn when you open the door. I then removed the two screws holding the front together. after tilting the front out i was able to place the slides in without having to pull of the front entirely.

First I removed the 2 screws that hold the lid down. Then I pulled the lid off. Then I removed the 2 screws that hold the front of the dryer in place. Then I lifted the drum a little and pulled the front cabinet out a little so I could see the drum slides. I removed the bad drum slides and installed the new ones. I then put everything back together and turned on the dryer. The squeeky noise was gone.

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.

I ordered to timer knob. Its was delievered in two days. When I received it, My bother and I looked at it expecting more than what we received, We said to each other this isn't going to work. I told my bother to go on and try it anyway. He took the old timer knob off and then removed a clamp at the base of the timer knob fitting. He then placed the timer knob back of the fitting. Turned the dryer on and it started right up. We were both shocked that it ran and that it was so easy to fix. Thank you PartSelect. Great customer service. I have already ordered a part for his refrigerator! Can't wait till we get the part. I'm sure its going to work just fine.

My husband snapped the new know easily into place.

I was tired of the process after having the know break three times in less than three years which makes me think there is a design flaw.

I simply removed the switch and matched the pole numbers to the new switch eventhough the new switch had two extra poles. The switch replacement was straightforward and worked very well.

Replaced drum bearing part and white slides.The problem was that it was not the drum slide support. It appears to be the the drum rear bearing of whch I am now ordering. The bearing replacement is a little more difficult, but I have taken this on as a challenge

1st I suspected it's just the timer knob so I ordered the knob. Soon as I was installing the knob it was too loose, when I inspected the timer stem it was also broke. So I ordered a timer. Soon as the timer arrived, I installed the timer and tested the dryer then it came on.

TOO EASY to repair. WORKS GREAT>

1) Disconnect power supply. 2) Open dryer door to find and remove two screws through dryer top. 3) Proceed to lift front dryer top panel and tap rear of dryer top with hand to left to disengage tabs and remove dryer top completely. 4) Remove two screws through front panel. 5) Gently lift dryer front panel from base tabs to partial remove panel (careful of wires which remain connected) - pivot front panel to left with wires connected. 6) lift dryer barrel with left hand / reach under barrel with right hand to release belt from tensioner pulley (very easy one-hand maneuver). pull dryer barrel belt off tensioner pulley towards you, remove belt from motor pulley below. 7) lift/pull and remove dryer barrel and belt (flex side panels). 8) take picture of wire connection locations on heating element and remove wires from tabs two locations / 3 wires. 9) remove sensors 3 locations. 10) remove heating element and housing. 11) install new heating element / housing and reverse process. .....tip; belt tensioner pulley was biggest challenge at first because it was hard to see how it all worked and reach. once i realized i could force / lift the barrel up to gain better access it was much easier than trying to fit my arm through the one large available hole at bottom right (when looking at the unit). the tensioner pulley is opposite side (left when facing) and you would have to reach over the exhaust, etc.