DNXR473GW2WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Wayne from Fort Washington, PA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Squeeky Noise When Dryer Was Running
First I removed the 2 screws that hold the lid down. Then I pulled the lid off. Then I removed the 2 screws that hold the front of the dryer in place. Then I lifted the drum a little and pulled the front cabinet out a little so I could see the drum slides. I removed the bad drum slides and installed the new ones. I then put everything back together and turned on the dryer. The squeeky noise was gone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Sterling Heights, MI
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
worn dryer drum slides
i first popped off the top of te dryer after removing the two screws in frotn when you open the door. I then removed the two screws holding the front together. after tilting the front out i was able to place the slides in without having to pull of the front entirely.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from Redondo Beach, CA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
drum wore down plastic
pulled off the top, pulled off the front then replaced the plastic that was supporting the front side of the drum. fairly easy to replace although the little plastic 'slides' (you need 4 of them)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Sacramento, CA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer drum squealling
I followed the directions from the previous post. It was much easier than described. I got the part, removed 4 screws, removed the top, pulled the front and replaced the part. It was all together again in 15 minutes. Dryer sounds great again! I'm so glad I didn't call a repair man!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Middletown, NJ
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Dryer Knob
Removed and replaced knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shauna from Bend, OR
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
High Squeaking noise
I removed the top of the dryer and saw that the top two drum slides where gone and the drum bearing itself was damaged I Temporally placed the parts on the drum bearing until I got the new one, that stopped the squeaking noise. All I needed to do was place the part with the hole on the little hook and then sled the other part in its slot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Maryville, TN
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken knob
Used pliers to remove old clip. Installed new clip and knob. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanie from Barlow, KY
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken start knob on dryer
old dryer knob had lost its spring and would not turn on. simply pulled old knob off and replaced by pushing new knob onto shaft. voila! saved myself a service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rene from Winter Garden, FL
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastic Start knob broke
Just push the new knob over the metal pin
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from no. attleboro, MA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken knob on dryer
pushed replacement knob on shaft of dryer. machine works better than new. took less than 24 hours from time of order to time of delivery to my house.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Johnson Valley, CA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed a new knob for my dryer
All I did was stick the knob on. How easy was that! Knob works every time. Very pleased with the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adrienne from Beaver, PA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Start knob broke from being turned too far
Fortunately I watched the video on how to change the knob. I may not have noticed that the metal clip part of the old knob was still attached. Once the old part was removed, the new knob slid right into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffrey from hertford, NC
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Loud Squealling noise from dryer
Opened the door and removed 2 screws from inside/top of door. Removed top and then removed 2 screws from back of front panel. Lifted drum slightly to remove front panel and attached new slides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Valdosta, GA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The old knob hasd split and wouldn't turn the dryer on
I took the visegrip pliers off the d shaft and simply slid the new knob on with ease. I never doubted my abilities!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erin from Tucson, AZ
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken knob
The old knob broke off & was no longer able to turn the pin to start the dryer. I simply slid the new knob onto the pin & it worked like new.
Was this instruction helpful to you?
Thank you for voting!