DISR333FC3WW General Electric Dryer - Instructions

Shortly after a piece of felt (the duct felt seal) was visible on the drum intererior, the dryer started making metal-on-metal squeaks. A few weeks later it started leaving'machine part' type brown/black marks on clothes. With the model # it was quite easy to find and order the correct part, which arrived a few days later. The accompanying video made installation quite straightforward, even for someone who's NEVER worked on a dryer before - even though the model used wasn't the same. Over half the repair time was to clean out lint and dirt from the various exposed parts. Overall, an easy and effective repair that solved the staining issue. Follow the video and you won't go wrong.

The instructions that came with the bearing were limited and the illustrations were too dark to see. However, after reading the reports of others on this website, the repair was very easy.

Prior to disassembly, remove theaccess panel on the rear of the dryer. Pull the belt drive pulley arm up and the belt will easily slide off of the motor pulley. The belt can be left on the drum.

Then, remove two screws at the inside top of the dryer door. The top of the dryer will then lift up at the front and slide forward to remove. This will allow you access to two bolt head screws on each side of the front panel. Remove these two screws and then lift the panel slightly up and forward. The front panel will then be free and the dryer drum will slide forward and out. Remove the four bolt head screws (behind the electric elements) from the heater element on the inside back of the dryer box.

You can now exchange the bearing on the drum and the bearing insert on the dryer heating element simply by removing the old and reinstalling the new just as the old was removed - four screws for each.

You will need an assistant to re-install the bearing. Someone needs to hold the three pieces behind the drum as you insert the three screws. You'll also need a star wrench set for this.

The drum is easily reinserted - just be careful to get the front of the drum placed into the front bearing surface when reinstalling the front panel. One word of caution, My wife tried to remove the felt bearing on the bottom of the front panel thinking that it was lint.

I found that the inside of my ten year old dryer was unbelievably full of lint. I'm sure that the efficiency improvements by cleaning the air passages will be substantial and I've just saved $400 on the price of a similar dryer ($900 if my wife and I decided to upgrade to the "new" model that we wanted but really didn't need.

Removed top - 2 screws. 2 more and the front comes off. I left the wires connected, and leaned the front against the wall. I then popped the drum bearing, with the slides off of the front, and pulled the felt from the lower half. I took some extra time cleaning lint with a shop vac. I then assembled the new parts back onto the front, and pulled the felt into position - it was a little fussy getting it right. The front panel and the top go back, and it`s done. I am glad I ordered the drum bearing, as the felt was worn much more than I would have guessed. This job could probably be done in 15 minutes next time, not including lint clean-up.

Drum was misaligned and scraping againt the appliance housing due to worn-out slides.

Replaced the drum slides 2 - white, 2 - black. Replaced the slide housing (front drum bearing?). This part was worn due to worn-out slides that were missing.

Cleaned out old lint from rear of drum and appliance housing. Put new weather stripping seals on the lint catch exhaust. Checked drum belt for cracks and checking.

Buttoned everything back up and dryer works as good as new. $60.00 for parts, 1 hour labor and the job was done!

Removed top panel giving access to drum and screws that hold front panel (door). Removed to screws to be able to remove front panel but be careful wires are short not giving you much room to remove panel. Removed plastic Drum Bearing and replaced with New one. Installed slides and put back together.

First I watched the repair video on partselect.com and that really helped. It was really easy to replace the slides. I even ordered a new top bearing, old one was busted, and replaced it. Thank you for your help.

With the help of doityourself guy on the internet

I removed several torx srews across the back control panel. Removed two philips screws under top of front dryer door. Pulled up on top surface of dryer case. Removed two more screws on backside of front door panel. Pulled front door panel forward and inserted drum slides into slots that they just popped into with a small button rod to keep them in place. The old drum slides were completely worn down or fell off. It runs like a new one again. It is over 10 years old.
The new door handle just snapped into place.
Original door handle had been broken off for several years.

Gently pull off all knobs and put aside. Remove the panel screws using the star bit. Tip panel forward. Remove three wires from old switch and put them on same terminals on new switch. Use the screwdriver to gently pull up the old switch's locking arm from the slot in the front panel and rotate the old switch until it pops out of the front panel. Insert the new switch into the panel and rotate until the locking arm clicks into place. Replace front panel making sure no wires are pinched. Re-install the front panel screws and control knobs.

Followed the directions in the video. The only problem was there was no mention of needing a star bit set in addition to a Philips screwdriver in order to get the back splash detached from the dryer. This is probably because the machine was 11 years old. It would have been more helpful to have a note that machines prior to a certain age would need that tool. Otherwise it was a easy job even for a 75 year old grandmother.

had a great video to follow, made it easy to install.

The repair went very well, parts fit perfect. Now there isn't anymore complaints.

First thing I did was find out the model and serial #'s of the dryer. I went to a major store to see if they had the part, found out that it had to be ordered and mailed to me. I decided to do it myself, I found your website and I ordered the part. I saved $10.00 by doing this. The part was very easy to remove and install. I just had to remove a small clamp that held the part on to the machine and make sure the 3 wires were secured after I installed the new part. Thank you!

Old handle popped out by pulling back and out. Inserted new handle by pushing in and forward. Easy!

All I neede to do was buy the new part and snap it into place on the door. The hardest part was making the door usable while waiting for a new handle. The solution was good old duct tape. I just taped the old broken handle in place until the new one showed up.