GTD84ECSN2WS General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from HILLIARD, OH
- Parts Used:
- WE10X23891
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Original door was broken. It had to be replaced.
Replacement door came with hinges. Removed four Phillips head screws, removed original door, and replaced it with the new door. Because I needed to move the dryer to allow room to get to the screws, I needed about 15 minutes to complete the project.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARTIN from MOUNTAIN VIEW, WY
- Parts Used:
- WE1M825
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
WAITING ON PART
Still waiting for your parts. over two weeks to get part which was a hinge for something, I don't know what, but not my dryer seal. You said you would refund shipping and wrong part and charge me for a new order. End result was I got charged extra shipping for your mistake. The part still is MIA and it has been 5 weeks since I originally ordered. Will never do business with you again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cary from SILVER SPGS, FL
- Parts Used:
- WE04X28977
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
When the door is closed the dryer didn't work
Easy watch YouTube and open door placed screwdriver under door switch pry lightly and switch will pop out unplug wire connectors and replace on new switch reinsert switch should be done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from LEVITTOWN, PA
- Parts Used:
- WE11X21156
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
no heat from dryer
used you tube and with your info. actually took apart dryer replaced part & reassemble
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Enterprise, AL
- Parts Used:
- WE1M462
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud noise
With the help of doityourself guy on the internet
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DECATUR, GA
- Parts Used:
- WE03X37320, WE03X37319
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Replace the front slides and glides on the dryer
To get to the slides, needed to take off the front panel, the top and then can loosen the front of the dryer. Pull it out enough to get to the slides and replace them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from CONNELL, WA
- Parts Used:
- WE03X37320, WE03X37319, WE09X27634
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Black marks showing up on garments.
Once I figured out how to remove the control panel. The rest was very easy. Upon pulling off the knob in the center of the control panel, there was a screw behind it. Once removed I used the palm of my hand and gave it a couple of upward hits in the center while the door was open. It slid up and I removed the electrical connections. Then carefully removed the top by pushing from the rear of the machine slightly and lifted off. Then removing the screws that hold the front on . After that it went pretty easily, reassembly went in reverse and. That was that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from GUILDERLAND, NY
- Parts Used:
- WE04X28977
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
The dryer would not start.
The entire dryer had to be taken apart to get to the door switch. I determined the door switch was faulty by measuring conductivity. I purchased the new switch which cost about $9. The shipping cost was $9. After all that, the dryer still won't start. I gave up and bought a new dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from OLD TOWN, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No power to dishwasher
Replace both micro switches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from ATWATER, OH
- Parts Used:
- WE04X28977
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
After closing dryer door unit would not start after several attempts.
Pry out switch with screwdriver. After removing switch unplug electrical leads from old switch. Plug leads in new switch and reinstall switch in dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manuel, J from MCALESTER, OK
- Parts Used:
- WE4M325
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Original terminal grounding block melted for unknown reason.
Unscrewed the old, screwed in the new making sure wires matched up same as before. Reset my breaker and works like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from WACO, TX
- Parts Used:
- WE2M302
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Reversing the dryer door.
Removed 4 #1 Philips screws from 1side and add to the other side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LARRY from HAMILTON, OH
- Parts Used:
- WE4M325
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
When moving the dryer there was a loud pop and the dryer circuit breaker tripped.
When the dryer was installed last year by the dealer, one of the hot leads was not screwed down tightly. Over time the screw loosened and began to arc causing the plastic holding the screw to melt. When I moved the dryer the hot lead fell off and hit the terminal block cover shorting out the dryer. I was able to locate the exact terminal block I needed with their helpful dryer section diagrams. The part came in the time they said. I took off the old terminal block with just 2 attached screws. i kept track of which screws held the hot and neutral conductors and the ground before I removed them. I was then able to slide on the dryer wires and attached the home conductors. I put on the cover plate, turned on the circuit breaker and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Saint Louis, MO
- Parts Used:
- WE09X27634
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Squeaky dryer
4 screws, that was it
open the dryer door, locate the 2 screws that hold the top in place, unscrew them
then locate the 2 screws (located near the top of the dryer (facing toward you) and unscrew them
allow the front of the dryer to tilit out towards you, replace the felt, slide the drum back into place into the front of the dryer, resecure the 2 screws (removed last)
lower top of dryer back in place, being careful to make sure the top clips back in correctly.
re-install the 2 screws that secure the dryer top to the front.
boom, you are done....
Amazingly easy work...
open the dryer door, locate the 2 screws that hold the top in place, unscrew them
then locate the 2 screws (located near the top of the dryer (facing toward you) and unscrew them
allow the front of the dryer to tilit out towards you, replace the felt, slide the drum back into place into the front of the dryer, resecure the 2 screws (removed last)
lower top of dryer back in place, being careful to make sure the top clips back in correctly.
re-install the 2 screws that secure the dryer top to the front.
boom, you are done....
Amazingly easy work...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from Westfield, NC
- Parts Used:
- WE09X27634
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Squeaking Dryer
The top and front of the dryer had to come off, and taking off the top (and later putting it back on) was the hardest part. The old seal was stretched approximately two feet longer than the replacement part, and its thinness caused the drum to squeak as it scraped by the door panel. We simply pressed the new seal into place after pulling out the old one. Piece of cake. Putting the front of the dryer back on was simple as well. Fitting the top back into its slots properly was the biggest pain of the whole ordeal. The part came in about 2 days. Thanks!
Was this instruction helpful to you?
Thank you for voting!