GTD58EBSV0WS General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from BREVARD, NC
- Parts Used:
- WE11X29438
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Heat deflecter coated with plastic from drying plastic table cloth.
Advice from others with same problem on your web site was very helpful. I removed one of the three torx screws holding the deflecter, Used 2.5 star-drive screw diver bit and cordless drill/driver. Replaced 2 of three torx screws holding the deflecter with the headless brass screws, Using vice grip to tighten. Removed third torx screw and removed old deflector. Used shop vac to clean behind it. Installed new deflector, sliding it over the 2 headless screws, then installing one of the torx screws, then replacing the brass screws with original torx screws, one at a time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from OKLAHOMA CITY, OK
- Parts Used:
- WE03X23881
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The lent filter was worn out, the screen was ripped and torn from west.
Very simple and easy it took no more than 10 seconds if that long. Remove the worn out screen (pull up and out), replace it with the new screen( slide it into the area where the old screen was removed. (No tools needed)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rene from LAUD LAKES, FL
- Parts Used:
- WE01X25317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Door Hinge
Having 2 persons make the job easier.
1) Remove the screws that holds the hinge to the body of the unit.
2) Remove the screws around the door so you can get to the hinge.
3) Remove bad hinge and replace with new one.
1) Remove the screws that holds the hinge to the body of the unit.
2) Remove the screws around the door so you can get to the hinge.
3) Remove bad hinge and replace with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebekah from NEW ORLEANS, LA
- Parts Used:
- WD21X10261
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My dishwasher would not start.
I unscrewed the inside of the dishwasher door and clearly saw the old interlock switch. This dishwasher has two, but it was obvious that one switch worked and one didn't (one switched was permanently pressed in). I removed the old interlock switch. It was tricky to pull out and I felt like I was going to break it but after watching youtube videos, I was pretty sure you just have to pull hard. I easily put the new switch in, reattached the dishwasher door, and it works perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth A from STEVENS POINT, WI
- Parts Used:
- WE03X23881
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Torn screen on lint filter
Just put new lint filter in slot
I had torn the screen on the original one
I had torn the screen on the original one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from phenix city, AL
- Parts Used:
- WE03X31620, WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
belt was broken.
remove top of cabinet and front panel. placed belt around drum and replaced idler pully placed new belt around pully and was done. not a hard job at all. replced front panel and top. thanks to a speedy delivery of my parts dryer was only down two days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from SUN CITY WEST, AZ
- Parts Used:
- WE03X23881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Lint filter in the dryer was damaged from continuous use.
I just popped in the new Filter and it fit perfectly. This will prolong the dryer use, looks like new.
Thank you Part Select.
One Happy customer
Thank you Part Select.
One Happy customer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from MARENGO, OH
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher wouldn’t start
Took the screws out of the back of the doorl located the switch and replaced it put screws back in and it was fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dameon from SMYRNA, DE
- Parts Used:
- WD21X10261
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Dishwasher would not start
Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from NOVATO, CA
- Parts Used:
- WE01X25160
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Needed a shoe rack
Lift the lint filter and slide the 2 hooked ends into the 2 holes provided . Front end is locked in as other end is suspended .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from CORP CHRISTI, TX
- Parts Used:
- WE04X26139
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer would not start.
Found the dryer's high limit thermostat had opened up.
Likely cause was excessive lint buildup in exhaust vent pipe to outside.
Used wire nuts to "temporarily" bypass thermostat and cleaned out the vent pipe
When new part arrived...
Removed control panel screws and panel was laid on top of dryer
Removed back panel screws.
Removed top panel screws. Lifted to allow right side swing out slightly.
I did not have sufficient tool to reach the thermostat therefore I reamed out a hole in the rear panel above the thermostat fastener screw to allow a long handle screwdriver into the area for replacement.
Removed temporary bypass and used wire nuts to utilize dryers' thermostat existing wiring.
Likely cause was excessive lint buildup in exhaust vent pipe to outside.
Used wire nuts to "temporarily" bypass thermostat and cleaned out the vent pipe
When new part arrived...
Removed control panel screws and panel was laid on top of dryer
Removed back panel screws.
Removed top panel screws. Lifted to allow right side swing out slightly.
I did not have sufficient tool to reach the thermostat therefore I reamed out a hole in the rear panel above the thermostat fastener screw to allow a long handle screwdriver into the area for replacement.
Removed temporary bypass and used wire nuts to utilize dryers' thermostat existing wiring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from ROLESVILLE, NC
- Parts Used:
- WD21X10261
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
dishwasher did not start
Took out interlock switch (two leads) and replaced with new one. As simple as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sydrell from CHICAGO, IL
- Parts Used:
- WE03X23881
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the bracket around the net was cracked
removed old lint trap cleaned excess lint that fell inside from the broken lint trap made it easier for new lint trap to slide in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerard from goldsboro, NC
- Parts Used:
- WE09X27634
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
the felt in front door worn out
i follow your video and all went well except now the dryer will not heat. i went back on your site an tried the no heat option an still no heat
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Armando from WESTMINSTER, CO
- Parts Used:
- WE03X23956
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer drum started making a grinding noise and started to smell like something was burning
Took the front panel off. 2 screws on top of the front panel when you open the door, 2 right next to the door opening. Next gently pry up the top panel in the front of the dryer to remove 2 black screws in the front corners. Now the front panel can gently be pulled back and then lift up and the frpnt panel can be put to side. Now you have acces to remove and replace the drum bearing glides. They just clip in. Also a good time to inspect the belt and clean out the dryer.
Was this instruction helpful to you?
Thank you for voting!