DSKS433EB7WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jean from Waterford, MI
- Parts Used:
- WE1M1011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The dryer door wouldn't stay closed.
There is a plastic female closure part in the dryer door that wouldn't close tightly around the metal male closure on the dryer. I popped out the plastic square with a screwdriver, popped the new plastic closure in with my thumb. Works great. I never even installed the new metal portion of the latch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Summerdale, PA
- Parts Used:
- WE4M415
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer would run for 4 minutes and shut off. keep turning it on
Faulty Door switch. Dryer would heat up so I knew it wasn't thermostat or element related.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Cumming, GA
- Parts Used:
- WE4M415
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer makes noise when "Start" is pushed, but stops when you let go.
Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Richmond, VA
- Parts Used:
- WE4M415
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Dryer would not turn on
It took a while to diagnose the problem. I finally figured out it was the door switch by pushing it with my finger with the dryer door open and starting the dryer. It would run like that, but the switch was not being pressed in enough by the door. I ordered the switch and I should have been able to replace in about 15 min. But the old switch broke while I was removing it and it fell back inside the unit. So I had to remove the top and the front panel to access the door switch. That's why it took so long. If that had not happened it would have been a much simpler repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis G from Naples, FL
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Holes were not threaded on rear bearing kit
Had to tap three holes in the rear bearing to match the three attachment screws. Screw up with the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Oregon, OH
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Loud Squeek When Started until warmed-up
Ordered the recommended parts on-line and they showed up the next day. I followed the on-line repair video that described it all step-by-step.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Hopatcong, NJ
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Loud screeching noise
I watched video supplied from parts select, only took about 30 minutes, hardest part was putting belt back on, couldn't fit hands in easily, but once I did it, dryer is like new, can't hear a thing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from easton, PA
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dishwasher door switch
unplugged old switch and installed new one. it took 5 minutes to do. 20.00 saved me 400.00 on a new washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fawn from Loganville, GA
- Parts Used:
- WE1M1011
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door would no longer shut.
Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Riverview, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The unit would not start.
First I turned off the breaker to the dishwasher. I then removed the bolts that held on the inner cover(note the two small bolts go on the bottom one on each side). I lifted the switch up and disconnected the wire clips from each side. I then put the new switch in place with the wires attached. Then replaced the cover and screwed it into place. Closed the door and flipped the breaker back on and turned the dish washer on and it started up. A very easy replaceable part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Redondo Beach, CA
- Parts Used:
- WE1M1011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer door would not stay closed
inserted the latch into the opening in the front face of the dryer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michell from Bellefontaine, OH
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Loud Sqeaking noise
the replacement part was easy to replace but remembering how the belt went back on took alittle more time..
Was this instruction helpful to you?
Thank you for voting!