XTD72G8ST0WS General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rebekah from NEW ORLEANS, LA
- Parts Used:
- WD21X10261
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My dishwasher would not start.
I unscrewed the inside of the dishwasher door and clearly saw the old interlock switch. This dishwasher has two, but it was obvious that one switch worked and one didn't (one switched was permanently pressed in). I removed the old interlock switch. It was tricky to pull out and I felt like I was going to break it but after watching youtube videos, I was pretty sure you just have to pull hard. I easily put the new switch in, reattached the dishwasher door, and it works perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth A from STEVENS POINT, WI
- Parts Used:
- WE03X23881
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Torn screen on lint filter
Just put new lint filter in slot
I had torn the screen on the original one
I had torn the screen on the original one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from SUN CITY WEST, AZ
- Parts Used:
- WE03X23881
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Lint filter in the dryer was damaged from continuous use.
I just popped in the new Filter and it fit perfectly. This will prolong the dryer use, looks like new.
Thank you Part Select.
One Happy customer
Thank you Part Select.
One Happy customer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from MARENGO, OH
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher wouldn’t start
Took the screws out of the back of the doorl located the switch and replaced it put screws back in and it was fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dameon from SMYRNA, DE
- Parts Used:
- WD21X10261
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Dishwasher would not start
Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lewis from WESTFIELD, NJ
- Parts Used:
- WE03X31620, WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Noisey squeaking noise.
Replaced the rear drum bearing, Front drum bearing,front bearing tabs and belt. I replaced the belt from the front of dryer. Better to go thru the back. Much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from LAWRENCEVILLE, GA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The dryer drum wasn't spinning, but I could hear the motor and feel the heat from the heating element.
UNPLUG the dryer. I removed the top panel by removing the two screws at the top of the dryer door. There are some hooks toward the back of the top panel, so you'll need to slide it to the left to get it off. The front panel needs to be removed by removing two screws just inside the top left and right corners. Lift and set it aside. I didn't disconnect the door wiring, but you can if you need to do so. I just spun the front panel to the left and out of the way. With the drum exposed, I confirmed the belt was broken. I replaced the belt, then the front panel and top panel. While I was inside the dryer, I did a through cleaning with the vacuum to get all the lint.
The video on the site is easy to understand and a snap to follow.
The video on the site is easy to understand and a snap to follow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from NOVATO, CA
- Parts Used:
- WE01X25160
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Needed a shoe rack
Lift the lint filter and slide the 2 hooked ends into the 2 holes provided . Front end is locked in as other end is suspended .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from WALHALLA, SC
- Parts Used:
- WE04X24550, WE01X24552
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
timer control locked down, knob was broken trying to turn
took 6 screws 0ut of cover plate,removed wires one at a time and replaced on new part(timer) removed retaining scres turned 1/4 turn removed--replaced in reverse manner
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rafal from FSTRVL TRVOSE, PA
- Parts Used:
- WE04X26138, WE04X25201, WE04X25199
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Not drying
Removing top of the dryer removing the back side panels of the dryer pulling back the back of the dryer to access to the thermostats left in the drum up to put it in the place secure all the screws and put everything together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MILLEDGEVILLE, GA
- Parts Used:
- WE01X24552
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
old timer knop cracked
stuck new knob on spindle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from ROLESVILLE, NC
- Parts Used:
- WD21X10261
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
dishwasher did not start
Took out interlock switch (two leads) and replaced with new one. As simple as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from BUFFALO, NY
- Parts Used:
- WE01X24552
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer timer knob
Dryer knob was not clicking on timer. Took knob off &saw that was a crack in it. Looked up model #&went on your website&ordered the same knob. Received quickly. Put the new knob on &itworked.Just had to line up 2 flats parts on knob & dryer.went right on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sydrell from CHICAGO, IL
- Parts Used:
- WE03X23881
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the bracket around the net was cracked
removed old lint trap cleaned excess lint that fell inside from the broken lint trap made it easier for new lint trap to slide in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from YOAKUM, TX
- Parts Used:
- WE04X28977, WE05X20431
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
WOULD NOT START/ stopped in the middle of cycle
Ordered parts and installed with YOUTUBE video.
Model A little different than showed online, There was a Metal protector over the Door switch that need to be taken off before switch could be located.
After detachment of dryer door, easily pushed the seal to one side to dislocate the metal protector.
Would of took 30 minutes to complete if had not been for the Metal protector they added to cover the switch.
Model A little different than showed online, There was a Metal protector over the Door switch that need to be taken off before switch could be located.
After detachment of dryer door, easily pushed the seal to one side to dislocate the metal protector.
Would of took 30 minutes to complete if had not been for the Metal protector they added to cover the switch.
Was this instruction helpful to you?
Thank you for voting!