NTX62G8ST0WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Vincent from NORTHVALE, NJ
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drive belt for dryer frayed and making noise
Followed the online demonstration on the website when i ordered the part. The video was outstanding and easy to follow. I now have the confidence to make other minor appliance repairs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard A. from Little Elm, TX
- Parts Used:
- WD21X10261
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishwasher would not start
Took the back off/there were six phillips head screws. Took the protective cover off the Interlock Switches and found the problem. One of the buttons was jambed and would not move. I pulled the switch up and pulled the connecting wires. This took a little bit of doing as the connectors have been set for over 8 years. I used a pair of needle nose pliers. I reconnected the new switch and punched both switches and the washer started. It was an easy repair after that, putting everything back in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john l from cumberland, RI
- Parts Used:
- WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Belt Was Broken
I watched the installtion video and actually did it faster than the video and yes you do have to be careful of sharp edges I did cut one finger. Other than that no problem I was all back together and using the dryer in less than 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrea from Helena, GA
- Parts Used:
- WE09X27634
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Needed to change the felt due to a squeaking noise.
I'm a 90 pound mother of 4you and was able to fix this problem all by myself. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Riverview, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The unit would not start.
First I turned off the breaker to the dishwasher. I then removed the bolts that held on the inner cover(note the two small bolts go on the bottom one on each side). I lifted the switch up and disconnected the wire clips from each side. I then put the new switch in place with the wires attached. Then replaced the cover and screwed it into place. Closed the door and flipped the breaker back on and turned the dish washer on and it started up. A very easy replaceable part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Parkersburg, WV
- Parts Used:
- WE4X448
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer wouldnt stay heated
Took off the top cover then took off the front panel and installed the new coils on gas valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TIM from NORTH AURORA, IL
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bearings,belt squeaking
Unscrewed the top lid screws located in door opening.Removed lid.Unscrewed the front cover screws located at top corners of cover, underneath where the top lid was.Pulled out drum,removing belt at same time.Removed the rear bearing unit,installed new one.Really easy.Took front bearing off front cover,it just snaps on.Installed new bearing,with 4 new slides.Reassembled machine,replacing old belt at the same time.Done.It really is that easy.Spent more time cleaning lint out of dryer interior than actual mechanical work,I think.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JoAnn from Daytona Beach, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Would Not Start
Put part in. Put the door cover on & turned on & it worked. Thanks for having the part. So far, so good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Hilliard, FL
- Parts Used:
- WE14M104
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
burner assy rusted out at corners,spitting sound when on.
1. turn off gas.2. disconnect electric.3.Remove 3/8 gas line from rear of burner. 4.disconnect two electric connectors from gas valve assembly. 5.disconnect electric line from igniter. 6.remove two mounting sheet metal screws from front of gas valve assembly(5/16 socket). There also may be a screw holding assembly to the bottom plate.7. remove entire assembly from dryer by pulling out to the front. 8.remove igniter assembly and replace on new burner. 9. two sheet metal screws 1/4 inch hold burner assembly to gas valve assembly.10.Install in reverse order . it may take a few seconds for the gas to get down to the burner. don't forget to change over the air mix valve to the same place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances from Anchorage, AK
- Parts Used:
- WE11X29438
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
Plastic melted onto diffuser, requiring replacement
My son ordered the part, but gave up installing it. We called in a professional appliance repairman because the dryer had to be partially dismantled to remove the drum and a belt so three sets of holes could be aligned to secure the replacement diffuser. My daughter had to lend a hand to hold one piece in place while the repairman threaded the screws because the drum was too deep for him to be able to reach both front and back pieces. Definitely not a one-person job for this particular model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gayle from Philadelphia, MS
- Parts Used:
- WE09X27634
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The dryer wasnt drying as fast and was making a lot of noise.
Followed the directions from the video about that particular part. I am 57 and it was fairly simple to do.
Was this instruction helpful to you?
Thank you for voting!