Models > GTD65GBSJ4WS > Instructions

GTD65GBSJ4WS General Electric Dryer - Instructions

Jump to:

All Instructions for the GTD65GBSJ4WS
46 - 60 of 126
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Robert from DECATUR, GA
Parts Used:
WE03X37320, WE03X37319
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set, Wrench (Adjustable)
Replace the front slides and glides on the dryer
To get to the slides, needed to take off the front panel, the top and then can loosen the front of the dryer. Pull it out enough to get to the slides and replace them.
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Scott from Poughkeepsie, NY
Parts Used:
WE03X29897
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Dryer Not Starting
First I replaced the timer, but dryer still did not start. took apart dryer, jumper out door and componet near motor to see what problem was and to be able to run dryer while opened up. Actually motor had seized up just enough to not allow motor to start rotating. Lubricated motor shaft and rotated motor for oil to work its way in. Tried starting again and motor started. Buttoned dryer back up and reconnected wires to appropriate places and started dryer again and again.Worked for 4 loads of laundry and still working for 3 loads on Wednesday. Working fine
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
rodney from VANCEBORO, NC
Parts Used:
WE03X29897
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
belt broke on dryer
good replacement procedure on you tube.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeff D from NEW MEADOWS, ID
Parts Used:
WE03X29897
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Drum would not turn
Exactly how your perfect video instructions showed me. Thank you for a job well done!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Bristow, VA
Parts Used:
WE03X37320, WE03X37319
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Rubbing noise while dryer was running.
After watching the video, the repair was very simple. There were no hiccups along the way. Special mention: the customer service is the best I've ever interacted with. Thank for making this a stress free experience.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from OLD TOWN, FL
Parts Used:
WD21X10261
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
No power to dishwasher
Replace both micro switches.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chris from WACO, TX
Parts Used:
WE2M302
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Reversing the dryer door.
Removed 4 #1 Philips screws from 1side and add to the other side.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from ATWATER, OH
Parts Used:
WE04X28977
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
After closing dryer door unit would not start after several attempts.
Pry out switch with screwdriver. After removing switch unplug electrical leads from old switch. Plug leads in new switch and reinstall switch in dryer.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Al from CORP CHRISTI, TX
Parts Used:
WE03X29897
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
BELT SQUEAKING
TOOK OFF TOP AND FRONT PANEL REACHED IN UNDER TUBE AND REMOVED FROM BELT TENSIONER HARDEST PART IS PUTTING BACK ON TENSIONER TAKES TWO HANDS LAYING ON YOUR BELLY
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Deerfield, IL
Parts Used:
WE14X215
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set
No heat from dryer. Diagnosed by others as the Gas Valve
Watched tecnician (I paid) as he diagnosed the problem. Four screws take of the top and front. Clothes drum slides out. Access to valve is good. Valve attaches to feed via compression fitting. Male end of fitting on unit is moved to new unit via allen wrench. Drive belt is re attached around drum and over idler easily. Part cost $90.00 shipp0ed to me. Technician asked $375.00 for this repair. Access the parts via placing the model number on Google Search.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cindy from EPHRATA, PA
Parts Used:
WE03X29897
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench set
Dryer needed a new dryer belt
I followed the directions I found on my tablet on youtube.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Phuc from WOODBRIDGE, VA
Parts Used:
WE03X29897
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
drive belt is broken.
Follow the instructions from YOUTUBE to replace the new drive belt..
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Arthur from GUILDERLAND, NY
Parts Used:
WE04X28977
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
The dryer would not start.
The entire dryer had to be taken apart to get to the door switch. I determined the door switch was faulty by measuring conductivity. I purchased the new switch which cost about $9. The shipping cost was $9. After all that, the dryer still won't start. I gave up and bought a new dryer.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kevin from RAPID CITY, SD
Parts Used:
WE20X25563
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
Instructions were a bid difficult to understand
I replaced the computer board on the dryer. Removing and replacing the backsplash and computer board were easy. Trying to figure out the GE model number and which code to use was a bit more of a challenge. The computer board works on three different models and you only have 1 chance to get the temporary code entered correctly. Information in the instructions on how to start over are very difficult to figure out.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Garry from CONNELL, WA
Parts Used:
WE03X37320, WE03X37319, WE09X27634
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Black marks showing up on garments.
Once I figured out how to remove the control panel. The rest was very easy. Upon pulling off the knob in the center of the control panel, there was a screw behind it. Once removed I used the palm of my hand and gave it a couple of upward hits in the center while the door was open. It slid up and I removed the electrical connections. Then carefully removed the top by pushing from the rear of the machine slightly and lifted off. Then removing the screws that hold the front on . After that it went pretty easily, reassembly went in reverse and. That was that!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GTD65GBSJ4WS
46 - 60 of 126