DCVH515GF3WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark from Monroe Township, NJ
- Parts Used:
- WE05X20431
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb
Open dryer door, reach in at the 12 o'clock postion
on the inside is the bulb.
on the inside is the bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from Wynnewood, PA
- Parts Used:
- WE05X20431
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb dead
remove the old one and put the new one...!!! Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Laurel Springs, NJ
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
dryer belt snapped
Replaced it as one would. I took off the front facing and replaced the belt. It took a bit of searching to find the proper way to route the belt around the pulley.
It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.
If I were to do it again, it would take 30 minutes or less.
It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.
If I were to do it again, it would take 30 minutes or less.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clarke from Grapevine, TX
- Parts Used:
- WE03X37317
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud squeek when dryer was running
Take out the two screws holding the top on with the door open remove top and remove two small screws in top front corners. I replaced the 4 slides and the drum bearing without the new felt, do not do this it continued to squeek after it ran the first few times when i got the new felt a week later i installed it in ten minuites and the noise is gone. I think it cost around sixty dollars and my dryer is back in action. Make sure that you clean all of the lint out of the inside of your dryer I had alot of build up near the chute for the lint trap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelly from MURFREESBORO, TN
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Squeaky dryer
I followed the YouTube video and it gave me step by step instructions however I really needed to replace my dryer slides to fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from EPHRATA, PA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
Dryer needed a new dryer belt
I followed the directions I found on my tablet on youtube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Rochester, NY
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Drum was squeaking and making a lot of noise!
Took apart the dryer housing fairly quickly, pulled out the drum, and installed the kit. Was fairly simple. Then reassembled. The hardest part was trying to get the belt on properly and reconnect to the motor. Believe it or not, I wasted most of my time on the belt. Should've watched the video better and listened to my wife and her suggestions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacqueline from FARMINGTON, ME
- Parts Used:
- WE05X20431, WE09X27634, WE03X37317, WE14M124, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The felt seal came out, and drum slides were cracked
We watched the YouTUbe video of Steve from this site and followed his instructions for how to replace the top bearing on the dryer, and the seal. It went quickly and easily, and his instructions were perfect. It helped that the model in the video matched ours almost exactly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phuc from WOODBRIDGE, VA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
drive belt is broken.
Follow the instructions from YOUTUBE to replace the new drive belt..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from BALTIMORE, MD
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud squeaking
Removed two screws, lifted the top, removed two more screws and tilted the front panel. The worn parts were accessible, and I simply placed the new parts in. It worked. A little trouble placing the top back in the slots, but a fist whack did the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from SICKLERVILLE, NJ
- Parts Used:
- WE03X37317, WE14M124, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
There was screeching noise during the drying cycle. Clothes being dried were getting stuck in the upper bearing.
I followed the instructions given in the video I watched when ordering the parts. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff D from NEW MEADOWS, ID
- Parts Used:
- WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Drum would not turn
Exactly how your perfect video instructions showed me. Thank you for a job well done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from CEDAR RAPIDS, IA
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bulb burned out
Unscrewed the old bulb using the lefty loosey method. Installed the new bulb by turning it clockwise or righty tighty.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from CORP CHRISTI, TX
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
BELT SQUEAKING
TOOK OFF TOP AND FRONT PANEL REACHED IN UNDER TUBE AND REMOVED FROM BELT TENSIONER HARDEST PART IS PUTTING BACK ON TENSIONER TAKES TWO HANDS LAYING ON YOUR BELLY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from BELFORD, NJ
- Parts Used:
- WE4M415
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Switch not working.
Open the door and removed the part. Installed the new part and started the dryer.
Was this instruction helpful to you?
Thank you for voting!