GTMX180GD5WW General Electric Dryer - Instructions

1. Turned off circuit breaker
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked

Repair was straightforward. You can change water inlet on this model from underneath in bottom from, although it is a little tight

It took longer to uninstall and reinstall the dishwasher than it did to change out the part

Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.

i follow your video and all went well except now the dryer will not heat. i went back on your site an tried the no heat option an still no heat

Originally I thought that the Start switch was the issue, and ordered one. After taking the machine apart and running some tests, the issue was clearly not this switch, but a different switch that cuts power when the belt tension is no longer being applied to the idler pulley spring. I fixed this by bypassing this switch, which in my opinion, is error prone and serves no purpose. The switch can be accessed by removing the control panel, then top cover, then front cover, then drum. The bogus switch is screwed to the bottom left, near the motor. The idler pulley spring rests against it. Just disconnect the switch wires, then clip, strip and crimp then together to bypass the switch, and voila! Now if the belt breaks or comes off the pulley, the motor will continue to run, but you wont hear the wet clothes flopping around, so that will be the indication that you have a belt problem. Hope that helps!

Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....

I was using vice grips to turn the control knob (stub) until the new knob arrived. The replacement knob was a redesigned type with a metal backing plate to place on the control knob stub (better than the original plastic knob) however the diameter of the new knob is only half the size of the original knob and the mark on the dial does not line up with the markings on the dryer control panel making it difficult to know what cycle you are using or how far to turn the dial within each cycle before passing to the next cycle.

Pulled off old knob and snapped new one into place. Took about 5 seconds. Must be a lame design cause my dryer's less than 2 years old and the knob snapped on the inside and wouldn't turn. Easy to fix though.

Tub gasket was a piece of cake, remove/replace by push in. Bottom door gasket was PIA. First you need to remove the door. Then, since the old gasket is held in place with a plate that is riveted together, you must drill out the rivets. Then you can install the new gasket. But first, you must use tap to replace rivet with threaded screw - unless you can find teeny tiny rivets!

The timer knob was sent, but the part on the dryer that was broken was a different knob. We were able to use the knob, but it was much bigger than the old knob.

I believe the diagram for the dryer showed the timer knob, but not the three other knobs.

I wish we would have received the correct knob, but the supplied knob is working for us.

Replaced the knob

removed old broken knob just pulled it off,replaced with new one took about five seconds.

Son found out where the bulb was by using YouTube. I googled lamp for model number and your website came up. I ordered the part, it arrived promptly, and my son installed it.

stuck it back in the holes just like the original handle. Had to do a little adjustment because I put screwdriver in them too many times to open the door after the original handle feel off, so the fit was loose. Fixed with tape.