GTR12BAXLWW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ronald from springfield, VT
- Parts Used:
- WR60X31522
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
noisy fan
removed cover over fan, four screws. removed two screws ,that holds fan in place,removed two more screws that holds fan in bracket,then reinstalled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from MELBOURNE BCH, FL
- Parts Used:
- WR60X10238, WR60X10207
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Motor making screeching sounds
Removed back panel
Unplugged wires to motor
Removed motor & fan assembly
Attached new fan to new motor
Attached motor to motor housing
Reattached wires
Reinstalled back panel
Unplugged wires to motor
Removed motor & fan assembly
Attached new fan to new motor
Attached motor to motor housing
Reattached wires
Reinstalled back panel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joan from STERLING HTS, MI
- Parts Used:
- WR60X31522, WR60X46086
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Fan not working
Took out old put new in. Watched a u tube, no problems
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ruoli from Germantown, MD
- Parts Used:
- WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Dryer's drum doesn't run
Follow YouTube "how to change dryer's belt" some video is very clear.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from SEATTLE, WA
- Parts Used:
- WR60X31522, WR02X12008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
the evaporator fan motor was making noise sometimes, but not all the time during the cooling cycle
after watching how easy it was to get to the evaporator fan motor on u-tube, I took out the motor to inspect it......the motor had about 1/8 inch shaft end play and a slight amount of play on the shaft, the rubber grommets looked OK.....I then put it back together......since the motor was the only moving part in this location I figured it had to be the part making the noise, so I ordered a motor and 2 grommets …...the replacement motor also had 1/8 inch end play on the shaft, but no play on the shaft....I installed the new parts and it has been a week now and no noise.....SUCCESS!...….the shaft on the motor protrudes from the motor, and the fan is mounted about 1 1/4 inch away from the bearing in the motor and the fan is unsupported, so I ASSUME that the slight amount of play on the shaft caused some harmonics which caused it to make noise some of the time, but not all of the time......
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from E NORTHPORT, NY
- Parts Used:
- WR17X11890
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken freezer door shelf
Just snapped in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from BELLINGHAM, WA
- Parts Used:
- WR22X10068
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
replace broken door dairy
a-ok. no problems
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lilly from CROSBY, TX
- Parts Used:
- WE01X20419
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
handle fell off
stuck it back in the holes just like the original handle. Had to do a little adjustment because I put screwdriver in them too many times to open the door after the original handle feel off, so the fit was loose. Fixed with tape.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- walter from STRATFORD, CT
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lint filter was broken
remove the broken one and replace it with the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from NEW BRITAIN, CT
- Parts Used:
- WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dryer bulb burned out
Son found out where the bulb was by using YouTube. I googled lamp for model number and your website came up. I ordered the part, it arrived promptly, and my son installed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from MURFREESBORO, TN
- Parts Used:
- WE01X20374
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The timer knob was cracked and wouldn’t turn properly
Replaced the knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from COVINGTON, LA
- Parts Used:
- WR09X20002
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The unit cycles but does not achieve proper temperature
Remove power from the unit. With short length #2 Phillips loosen and remove the two(2) screws on the control panel located center top of the refrigeration area. Slide the control panel back about 1/2 inch and allow it to dangle from its wiring harness. Pinch the locking tab on the harness connector with one hand and use the other hand to separate the two sides. A little force is required. Remove the control panel from the refrigerator and shut the refrigerator door. Examine and note the routing of the temperature probe (Silver colored flexible wire) take a picture for later reference. Remove the old and replace with new unit. route temperature probe like the replaced unit. Reverse the steps and reinstall the control panel. It is a good idea to also purchase and replace the defrost timer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- martha from Lehigh Acres, FL
- Parts Used:
- WR17X11662
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the frame was broken and it made using the shelf for food storage difficult.
Emptied the lower area of food, removed the drawers and the removed the broken shelf frame. My glass was unbroken so after removing it from the broken frame and cleaning it, I just had to place it in the new frame and put it in the frig. Can't believe how easy and quick the whole process was. I can now utilized all that wasted space in my frig again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- De Ann from FORKS, WA
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer was catching clothes and would not release without very hard pulling, consequently twisted and grease marked fabric, ruining items.
I followed the very easy YouTube video and got the three tools I needed before beginning. I started with removing the parts of the dryer and that was extremely simple by following the steps in the video. Took the door off last, located the parts that need replaced that didn't require any tools at all. Then put all the parts of the dryer back on in the order I removed them. The entire process was about 25 minutes but I would say I spent more time really cleaning the dryer and lint build up than actually doing the repair. Video was super thorough and easy to follow, I've never attempted any kind of repair of an appliance and I'm extremely happy that I had the video and the parts that were recommended to fix my problem, were spot on. Saved me hundreds of dollars and time. Thank you so much!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karl from Milford, NE
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Clothes were catching between the drum and front of dryer. Also was squeaking at times.
Opened dryer door and removed two screws that held front of top panel on. Lifted top panel off and removed two screws that held front panel to side panels. Tipped front panel forward and replaced all four slides. Cleaned everything off and put back together. Works great again. Thanks for this site and for others that have done these repairs before and posted their stories.
Was this instruction helpful to you?
Thank you for voting!