GTD75ECPL1DG General Electric Dryer - Instructions

Removed 4 #1 Philips screws from 1side and add to the other side.

When the dryer was installed last year by the dealer, one of the hot leads was not screwed down tightly. Over time the screw loosened and began to arc causing the plastic holding the screw to melt. When I moved the dryer the hot lead fell off and hit the terminal block cover shorting out the dryer. I was able to locate the exact terminal block I needed with their helpful dryer section diagrams. The part came in the time they said. I took off the old terminal block with just 2 attached screws. i kept track of which screws held the hot and neutral conductors and the ground before I removed them. I was then able to slide on the dryer wires and attached the home conductors. I put on the cover plate, turned on the circuit breaker and it worked.

Once I figured out how to remove the control panel. The rest was very easy. Upon pulling off the knob in the center of the control panel, there was a screw behind it. Once removed I used the palm of my hand and gave it a couple of upward hits in the center while the door was open. It slid up and I removed the electrical connections. Then carefully removed the top by pushing from the rear of the machine slightly and lifted off. Then removing the screws that hold the front on . After that it went pretty easily, reassembly went in reverse and. That was that!

Exactly how your perfect video instructions showed me. Thank you for a job well done!

The entire dryer had to be taken apart to get to the door switch. I determined the door switch was faulty by measuring conductivity. I purchased the new switch which cost about $9. The shipping cost was $9. After all that, the dryer still won't start. I gave up and bought a new dryer.

Unscrewed the old, screwed in the new making sure wires matched up same as before. Reset my breaker and works like new again.

Pry out switch with screwdriver. After removing switch unplug electrical leads from old switch. Plug leads in new switch and reinstall switch in dryer.

After watching the video, the repair was very simple. There were no hiccups along the way. Special mention: the customer service is the best I've ever interacted with. Thank for making this a stress free experience.

Remove top cover and front cover

Well, the intall would have been great except for the fact that I needed another part. If your belt breaks there is a reason for it. Make sure you check all the parts that work with the belt. Their was a pully the was defective and also need to be replaces. I think it would be a good idea to put a little note on the page for the Belt Drive to let people know that if you are replaceing the belt you might want to check the Idler Pully for it too might need to be replaces. I'm not an expert and if that was on the page for the Belt Drive I might have look at the pully before I ordered and I would have ordered the part along with the Belt Drive. As it was had to wait another 4 day to get my dryer fixed. I'm very happy the Parts Select has all my parts and they pretty good at getting them out to me in a good amount of time when I need them.

loosened two hose clamps and four screws to replace the anti siphon valve.

Un plug the dryer. Gather phillip, flat head and torix screw drivers. Remove the rear of the dryer to get the spec sheet with the appropriate part number. Next called for part. Belt installation requires removal of front and top of dryer in order to slide belt over the drum. Getting to all the fastners requires tilting the dryer on its back. Clean out excess lint from dryer interior and duct work. Slide drive belt over drum and use some masking tape to hold it in position. Reassemble dyer. Return dryer to upright position and put the belt on the pully and tensioner from rear access port. Remove tape. Replace access panel. Reattach vent duct work. Plug in. There are 5-6 different size screws holding everything together...you may want to use masking tape to label where each type of screw goes. All totaled it took about an hour and cost less that $25. Well worth the effort.

Removed the 3 star screws, putting in a piece if wire as I removed them. Wire was not stiff enough and let the drum slip thus binding making it hard to remove. Started over. Finally called a friend for help. I bought 3 tension pins the same size as the screws. When removing the diffuser screws, insert a tension pin in the hole as you remove each of the screws. The tension pins are hard metal and do not have a head. The diffuser will slip over them. After the diffuser was in place, we turned on the dryer to make sure it was running ok. I noticed what looked like lint toward the front. It was part of the felt gasket on the front of the drum and front of the dryer. We removed the screws on the dryer front and pulled it forward. The felt was rethreaded into its slot, put the front back in place,and replaced the screws that hold everything in place. If you turn the part of the dryer that spins by hand, make sure you are turning it in the correct direction. Turning it the wrong way is probably what caused the felt gasket to come loose causing more work.

I removed the two screws inside the door and popped the top loose. I took the top off to see and have access to the interior. I leaned the front out and inserted the belt around the drum (with my wife's help), replaced the screws and laid the dryer on it's face on a rolled up blanket and proceeded to run the belt around the pulleys (two). The drive pulley was easy but the idler pulley, not so easy. I had to figure out how the pulley arm was supposed to provide tension on the belt. I figured it out by looking at the diagram. It was then I found the idler pulley was broken and fell apart in my hand. I advise that a new pulley be installed at the same time as the belt. Everything I read on your web site helped.

Open up the unit's lid first and then removed the front panel. Then I removed the broken belt and then routed the new belt around drum, through the belt tensioner, and onto to the motor pulley. I checked to make sure the belt was securely in place and if it would rotate the drum. Once I was positive it was in place I put the dryer panels back together, plug in the dryer, and tested operation. The only thing that was difficult was trying to figure out the routing of the belt through the tensioner because the old belt wasn't in place anymore. In all it was a 45 minute job.