DPSB613EDC General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Low heat
Checked the fuse box to see if any breakers tripped on the two 120 lines feeding the dryer.
Checked for clogged exhaust vents/hose/etc, cleaned.
Some paint flaking off inner drum around heat vent.
Unplug & disassembled unit. Took pictures for reference to help with reassembly later. Upon removing drum, found sagging heat coils, one broken, some heat damage to the housing near the top. Determined that more than just coils needed replacing.
Also checked each of the three heat sensors (cycling thermostat, high limit thermostat & safety thermostat) with the digital multimeter. All were positive continuity for low temps.
Tested ONLY the cycling thermostat on the kitchen stove with burner set to warm. Check burner temp with meat thermometer to see it exceed 120F. Continuity broke at high temp. Although the cycling thermostat seemed ok with my generic test, I decided to replace it anyway.
My understanding of the Safety Thermostat & High Limit Thermostat is that they work like safety fuses, breaking at dangerous temps, but not resetting afterward. So these were only tested at room temperature, not with heat.
With the unit open, I checked other components for signs of wearing out. Also cleaned the unit more thoroughly.
Reassembled in stages. The belt is the trickiest part to get back on the motor & tension pulley, it's just a little awkward to reach. Tested to make sure the drum moved freely and belt was correct before finishing the reassembly.
Checked to make sure the dryer was still level, after all the moving around, disassembly & reassembly.
Ran several supervised test loads. Felt the temperature. No tripped breakers or smoke. Exhaust was flowing unhindered. Clothes got dry.
Checked for clogged exhaust vents/hose/etc, cleaned.
Some paint flaking off inner drum around heat vent.
Unplug & disassembled unit. Took pictures for reference to help with reassembly later. Upon removing drum, found sagging heat coils, one broken, some heat damage to the housing near the top. Determined that more than just coils needed replacing.
Also checked each of the three heat sensors (cycling thermostat, high limit thermostat & safety thermostat) with the digital multimeter. All were positive continuity for low temps.
Tested ONLY the cycling thermostat on the kitchen stove with burner set to warm. Check burner temp with meat thermometer to see it exceed 120F. Continuity broke at high temp. Although the cycling thermostat seemed ok with my generic test, I decided to replace it anyway.
My understanding of the Safety Thermostat & High Limit Thermostat is that they work like safety fuses, breaking at dangerous temps, but not resetting afterward. So these were only tested at room temperature, not with heat.
With the unit open, I checked other components for signs of wearing out. Also cleaned the unit more thoroughly.
Reassembled in stages. The belt is the trickiest part to get back on the motor & tension pulley, it's just a little awkward to reach. Tested to make sure the drum moved freely and belt was correct before finishing the reassembly.
Checked to make sure the dryer was still level, after all the moving around, disassembly & reassembly.
Ran several supervised test loads. Felt the temperature. No tripped breakers or smoke. Exhaust was flowing unhindered. Clothes got dry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from salem, NH
- Parts Used:
- WE03X29897, WE03X37317
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
slides worn and belt broken
Unplugged power. removed 2 screws to take of top cover. once inside removed 2 more screws to slide front panel of. I first replaced slides on front panel. I then lift drum and installed new belt. Only trick is to make sure you wrap belt around tension arm pully properly. Basically a very easy job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brad from Batavia, IL
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
loud screeching and long dry times
When we first heard the screeching i thought right away that it was the belt. we ordered a new one and after i replaced it the dryer was still just as loud. I wished i went here first. Right away i found others with the same problem, did the same repair which was just taking 2 screws out, sliding the top and front panel off(watch for the electric wire connected to the panel) and replace a couple of plastic slides. now it is better than ever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from west milford, NJ
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no problem
this was a part i ordered for future use. i was very happy with the ordering process and speed of delivery from PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Round Pond, ME
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My dryer was making a really loud, high pitched squeak and eventually a grinding noise
I order the parts needed to replace the slides, the felt ,and the bearing on a Sunday afternoon. The parts arrived on Tuesday even though I used regular shipping. I followed the instructions posted by another customer. It was extremely easy and only took me about fifteen minutes. My only problem was that I needed 2 each of the front slide and the rear slide, and I unknowingly only ordered 1 of each. I order the other 2 on Tuesday via regular shipping and they arrived on Wed. AMAZING!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARY from ERIE, PA
- Parts Used:
- WE18X25100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
remove plastic and insert
inserted the lint catcher into the opening to replace the old one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janet from martinsville, IN
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer did not latch
easy to fix took less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SONOMA, CA
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
thumping noise with any kind of load
looked at video of dryer disassemble, replaced 4 bearing slides, reassembled. Dryer is perfect now , no noise. thank you for your parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MEMPHIS, TN
- Parts Used:
- WE18X25100, WE05X20431
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old dryer filter was cracked and bulb burnt out
Easy peasey! Just Removed/Replace screw-in type bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from LOVELAND, CO
- Parts Used:
- WE18X25100
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replaced broken lint filter.
Removed the broken lint filter and replaced with new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from WHITE LAKE, MI
- Parts Used:
- WE9M13
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Gasket ripped
It was so simple. I removed the old ripped gasket by just pulling it. I followed the same direction with the new gasket by using a small screw driver to push in the tabs in each of the holes in the door. It works perfectly. They only fear I had was getting the part and the correct part, the model number of the dryer was on the door which made it easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from LUMBERTON, TX
- Parts Used:
- WE03X37317, WE03X29897, WE12X83
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Belt broke
Removed drum replaced pulley attached pulley spring to catch on motor bracket put belt on drum put drum in aligned belt and pulley released. Spring replaced door and top
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from COMSTOCK PARK, MI
- Parts Used:
- WE03X37317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Squealing as drum rotated
Removed the star bit screws on the top of the control panel then removed the front by opening the door and removing the screws in the upper corners of the door jam. I then removed the top which exposed the drum slides. NOTE: This model requires 4 drum slides and NOT two as specified in the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Kissimmee, FL
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud noise
First I watched the repair video on partselect.com and that really helped. It was really easy to replace the slides. I even ordered a new top bearing, old one was busted, and replaced it. Thank you for your help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph a from VALLEY STREAM, NY
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
belt broke
had a great video to follow, made it easy to install.
Was this instruction helpful to you?
Thank you for voting!