DVLR223EEW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- tim from NEW PRT RCHY, FL
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
evidently the pulley spring on video was very very very weak
the pulley spring took so much pressure to hold it down it took 3 men and a boy to hold it and place it in position to to get the belt on. Also there is not enough room to get your arms and hands in without getting some small cuts.Ultimately I removed the screws in the back of the dryer and spread the side of the dryer out to gain proper access. It was an easy repair if the spring would not have been so strong.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rodney from VANCEBORO, NC
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
belt broke on dryer
good replacement procedure on you tube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LARRY from HAMILTON, OH
- Parts Used:
- WE4M325
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
When moving the dryer there was a loud pop and the dryer circuit breaker tripped.
When the dryer was installed last year by the dealer, one of the hot leads was not screwed down tightly. Over time the screw loosened and began to arc causing the plastic holding the screw to melt. When I moved the dryer the hot lead fell off and hit the terminal block cover shorting out the dryer. I was able to locate the exact terminal block I needed with their helpful dryer section diagrams. The part came in the time they said. I took off the old terminal block with just 2 attached screws. i kept track of which screws held the hot and neutral conductors and the ground before I removed them. I was then able to slide on the dryer wires and attached the home conductors. I put on the cover plate, turned on the circuit breaker and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francisco from WEST COVINA, CA
- Parts Used:
- WE4M181
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
was not heating cheak parts select they recomended to purchaged the thermostat check vidio for installetion now working fine thanks
watched vidio from the site.just follow the instructions, And was able to fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Sugar Valley, GA
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
dryer had a loud sqeaking noise
removed top, 2 hex screws, removed front 2 hex screws & 2 star screws. removed belt, slid drum out. Removed old bearing and replaced with new bearing kit. assembled in reverse.
It would help to have another person assist you.
It would help to have another person assist you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from EASTON, CT
- Parts Used:
- WE12X83
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
Replace broken drum belt and belt idler pully wheel.
Watched video instruction, paying attention to what it showed in machine. Several virsions of similar designs over the years, look over yours and note access points, take pictures as you go! Just pay attention, it is very logical. Spread the side panels to get the drum in and out, and pay attention to drum axel in back and the bushing it rides in. Be patient, be firm but gentle, no real forcing needed if you are alligned. Be sure the grooves of belt are on the drum, drive wheel on motor, no twists. Reverse order to reassemble. There are several internet videos of models with same basic setup, so look at others if one doesn't show the detail you need to see, or clear some uncertainty. Your local hardware to sorce push fastening for the idler wheel to shaft if you mash it up, they are cheep and several styles will work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff D from NEW MEADOWS, ID
- Parts Used:
- WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Drum would not turn
Exactly how your perfect video instructions showed me. Thank you for a job well done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from WILDER, KY
- Parts Used:
- WE01X20419
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Door handle broke
Called my son-in-law. Easy as pie
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Renee from Leesburg, VA
- Parts Used:
- WE14X25080
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The dryer lint chute was cracked and catching our clothes.
We watched the YouTube video and had it installed in no time. Saved money doing it ourselves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Rochester, NY
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Drum was squeaking and making a lot of noise!
Took apart the dryer housing fairly quickly, pulled out the drum, and installed the kit. Was fairly simple. Then reassembled. The hardest part was trying to get the belt on properly and reconnect to the motor. Believe it or not, I wasted most of my time on the belt. Should've watched the video better and listened to my wife and her suggestions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Westminster, MD
- Parts Used:
- WE25M40, WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
clothes being eaten first then the loud noise
I replaced front and rear bearing.The rear I replaced because of cause and effect.There was some play so I am glad I replaced the rear too. Make sure you order drum slides. Ken
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelly from MURFREESBORO, TN
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Squeaky dryer
I followed the YouTube video and it gave me step by step instructions however I really needed to replace my dryer slides to fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Freeland, MI
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
loud noise when ran for 5 min.
Replaced the rear drum bearing. Not doing it before ,it took about 1 1/2 hrs. Problem was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phuc from WOODBRIDGE, VA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
drive belt is broken.
Follow the instructions from YOUTUBE to replace the new drive belt..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from EPHRATA, PA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
Dryer needed a new dryer belt
I followed the directions I found on my tablet on youtube.
Was this instruction helpful to you?
Thank you for voting!