DBSR463EG0WW General Electric Dryer - Instructions

The inner piece of the knob cracked so it just spun on the dryer shaft it's suppose to turn. Ordered a new knob, slipped it on and all works great again now.

I had already replaced the four (4) small wear strips which were like short strips of teflon, and the squeaking decreased almost completly. I noticed that front side of the drum itself had started to wear through the actual plastc drum bearing, but I hoped having previously replaced these tefon strips that would be the overall fix.
Wrong again... after a few weeks the squeeking continued until I ordered the new drum bearing and replaced the worn one with the new one. I was able to re-use the previous teflon wer strips, and it's like new now at least the squeaks are gone,

The actual fix was a very simple remove old drum bearing, snap in new drum bearing install old teflon wear strips put four screws in top, and front panel and I was back in business

I am a 55 year old woman who likes to repair household items. I followed You Tube instructions and did it all by myself. A few screws to get the top off and a two more to remove the front piece. Trap duct assembly was cracked and falling apart. Pulling off the old was fairly easy. I watched the You Tube instructions on my Ipad so I could rewind and watch as I did it. The hardest part was I dropped one of the screws when placing the front of the dryer back on and had to find another one that was the same size. Luckily I have lots of old screws in my tool box, If you like to do small simple repairs to save some money this is an easy one.

Removed that to screws for that top first and door shake top little to that front and I took two screws on that top each side and removed that front and lint trap and install the new

i follow your video and all went well except now the dryer will not heat. i went back on your site an tried the no heat option an still no heat

Pulled off old knob and snapped new one into place. Took about 5 seconds. Must be a lame design cause my dryer's less than 2 years old and the knob snapped on the inside and wouldn't turn. Easy to fix though.

Dryer is 3 yeras old. This dryer switch / start knob broke three times. First two GE repair fixed it. Charge was about $75 to $100. Then I found Parts Select, Who what great prices. Switch cost under $10. and took me 10 minutes to install. Dryer works great again. OH, I ordered an extra switch to have on hand.

I was using vice grips to turn the control knob (stub) until the new knob arrived. The replacement knob was a redesigned type with a metal backing plate to place on the control knob stub (better than the original plastic knob) however the diameter of the new knob is only half the size of the original knob and the mark on the dial does not line up with the markings on the dryer control panel making it difficult to know what cycle you are using or how far to turn the dial within each cycle before passing to the next cycle.

Just took out of plastic wrapping and put on dryer. No tools needed.

-- Unplug dryer from electrical outlet
-- Open Door
-- Remove two screws going up into the top panel
-- Remove top panel
-- Close door
-- Remove two screws holding front panel
-- Remove Front Panel by turning out, keeping left side close to unit since wires are still connected.
-- Vacuum out all loose dust/lint
-- Tilt old Drum bearing toward you to remove.
-- Remove Old Felt Drum Seal
-- Install drum Slides on new Drum Bearing
-- Install new Drum Bearing, make sure it clicks into place securely.
-- Install new Felt Seal, make sure to push in far enough to securely hook to the clips on the bottom of the Drum Bearing.
-- Reinstall front and top panels
-- Plug in electrical
-- Dry

I watched the repair video 3 times to make sure I was comfortable to do the repair.the video was very helpful.thank you ! Everything went well and the dryer runs great.

I followed the very easy YouTube video and got the three tools I needed before beginning. I started with removing the parts of the dryer and that was extremely simple by following the steps in the video. Took the door off last, located the parts that need replaced that didn't require any tools at all. Then put all the parts of the dryer back on in the order I removed them. The entire process was about 25 minutes but I would say I spent more time really cleaning the dryer and lint build up than actually doing the repair. Video was super thorough and easy to follow, I've never attempted any kind of repair of an appliance and I'm extremely happy that I had the video and the parts that were recommended to fix my problem, were spot on. Saved me hundreds of dollars and time. Thank you so much!

Checked the fuse box to see if any breakers tripped on the two 120 lines feeding the dryer.

Checked for clogged exhaust vents/hose/etc, cleaned.

Some paint flaking off inner drum around heat vent.

Unplug & disassembled unit. Took pictures for reference to help with reassembly later. Upon removing drum, found sagging heat coils, one broken, some heat damage to the housing near the top. Determined that more than just coils needed replacing.

Also checked each of the three heat sensors (cycling thermostat, high limit thermostat & safety thermostat) with the digital multimeter. All were positive continuity for low temps.

Tested ONLY the cycling thermostat on the kitchen stove with burner set to warm. Check burner temp with meat thermometer to see it exceed 120F. Continuity broke at high temp. Although the cycling thermostat seemed ok with my generic test, I decided to replace it anyway.

My understanding of the Safety Thermostat & High Limit Thermostat is that they work like safety fuses, breaking at dangerous temps, but not resetting afterward. So these were only tested at room temperature, not with heat.

With the unit open, I checked other components for signs of wearing out. Also cleaned the unit more thoroughly.

Reassembled in stages. The belt is the trickiest part to get back on the motor & tension pulley, it's just a little awkward to reach. Tested to make sure the drum moved freely and belt was correct before finishing the reassembly.

Checked to make sure the dryer was still level, after all the moving around, disassembly & reassembly.

Ran several supervised test loads. Felt the temperature. No tripped breakers or smoke. Exhaust was flowing unhindered. Clothes got dry.

Follow YouTube "how to change dryer's belt" some video is very clear.

Diagnostics, ordered front and back bearing. Added the belt because I was there. Parts came quickly. disassembled, shot photos of wire assemblies. Unprepared for element and lint trap housing failure as the heating element was only 1/2 functional, made followup ordered which included the green and white shims. Note, front bearing replacement does not come with wear shims, disappointing. Very inexpensive and should just be part of replacement package. Reassembled in reverse order, tricky part was the belt reinstall. New light made the repair complete.