DDC4580VA General Electric Dryer - Instructions

Pop off the old, pop on the new. I did it with one hand, the 'hard' part was putting the access panal back on.

unscrewed and lifted top of dryer put belt around drum closed top put belt around motor pulley and belt tensioner and finished.( remember to unplug unit before working on it.)

Based on the symptom (drum not turning), I figured that the belt was shot. I found a video on YouTube that described how to fix it. I also found directions here on this site on how to fix it! Here's what I did: step1: there were two screws holding the top on. took them off and the top swung up, exposing the drum and broken belt. step2: took off the two screws holding the front on. tipped the front forward so I could get the new belt around the drum. step 3: took the back plate off (10 screws). had to remove the exhaust tube first. cleaned out all the lint with the shop vac. there was plenty of lint everywhere. step 4: put the belt onto the motor pulley wrapping around the tension pulley. step5: put everything back together and plugged it in. everything worked fine. it took longer to vacuum all the lint out than it did for the actual repair.

Took off the top cover then took off the front panel and installed the new coils on gas valve.

I had to take the top panel off of the dryer which is 2 screws inside the dryer door jam. Then the front panel had to come off which was 2 screws inside the dryer above the tumbler. One on each side. Then it lifts off of two hooks at the bottom. Then the left panel (left if you are looking at the front of the dryer) had to come off which was a few screws on the back, a few on the front, and one on the bottom. Once I had the panels off, I unscrewed the blower wheel which is one screw. I took the blower wheel cabinet loose but didn't remove it. There is a metal collar that holds the motor to the bracket. Pull it off from the top. Unplug all the wires attached to the motor. I took a picture of the wire connections with my phone for reference with the new motor. Remove the belt. The motor should pull out towards you. The new motor comes with a pulley. Put the pulley on the motor and tighten locking screw. Put new motor in dryer and replace the metal collar. Connect all wire connections. Reconnect the blower wheel and tighten all screws to the blower wheel housing. Now, I plugged the dryer back in and tested it without reattaching the belt. Know that if you do it this way, the dryer will not stay on because there is a relay switch that is engaged only when the belt is on the pulley and there is tension on the belt tensioner. When the dryer motor worked properly, I replaced the belt and put all the panels back on. Plugged it up and it worked beautifully.

I suspected the idler pulley shaft was worn. I found the repalcement pulley on parts select web site. finding the part was very easy and delivery was very quick. After removing the dryer from the wall,I removed the access panel in the rear which exposed the motor, belt, and pulley. After removing the belt from the pulley, I removed the pully assembly from the dryer. I removed the keeper retaining ring on the pulley and installed the new pulley with the new parts supplied. The new pulley assembly was then ready for re-installation.

I watched Youtube videos on how to troubleshoot the dryer but I did not go through all the testing of the fuses and the heat sensor. I did not want to take the dryer apart if I didn't have to. I turned on the dryer and looked into the bottom grate and saw no glow from the igniter (it should be very bright) so I started there. (The Youtube videos test the igniter last). Unplug the dryer. Turn off the gas. Pry off the grate. Unplug the igniter connector and set the multimeter to tone on continuity. There was no tone so it was bad. I used a flashlight that I put inside next to the gas valve to see. Remove the top flat cover on the burner assembly, 2 screws. (Had to do all this laying on my belly in front of the dryer. Very uncomfortable.) Remove the old igniter from the clamp. It fell apart as I took it out. Now the tricky part: The clamp is very tight and the igniter is delicate. I tried to slide it in from the top holding it between my index and middle finger and lining up the slots for the igniter 'wings'. I struggled with that until many-swear-words-later, I decided to slide the igniter in sideways. Put the 'wing' into the clamp's left side opening and then gently but firmly squeezed the 'barrel' into the clamp. It worked. Plug in igniter plug, put burner cover back on carefully without banging igniter, turn on gas, plug in dryer. Turn on dryer. Igniter should be very bright when it lights. It takes a little while to heat up the heat sensor that will open the gas valve and the burner should light.

I was unsure of how to disassemble the machine to reach the belt, but a YouTube video gave me confidence. Thanks to Partselect.com, the great customer service, and fast delivery. I had my dryer up and running really fast! The process was really not difficult at all and it gave me a chance to vacuum out years of trapped lint. I am so happy to have saved hundreds of dollars, not having to buy a new dryer.I would urge other folks to tackle these relatively simple repairs, the right parts are a phone call away. Frank

Unplug dryer and turn off gas to appliance. Remove small vent door front of dryer for access to burner assembly. Reach inside and remove all three wires attached to the valve. Using a backup wrench remove the union that attaches the 3/8" gas line to the burner assembly. Remove the two bracket screws holding the assembly. The entire burner assembly can now be pulled out. Replace the faulty igniter by spreading the retainer clip and inserting the new part. Use extreme care not to touch the new igniter with bare skin...best to use a helper to assist holding the assembly while you insert the igniter. Then replace everything as you found it . Soap all gas fittings, plug it in and enjoy your dryer.

I didn't know what was wrong at first, only that the dryer would not start. I bought it used so had no fear of taking it apart to diagnose. Found the broken belt inside, ordered a replacement, installed the new belt, then crossed my fingers. Was pleasantly surprised that was all that was wrong and that for less than $20, including shipping, a few hours of my time, and a little help from YouTube videos the dryer is working again!

I was disappointed that there were No Instructions included with the part. So I found a you-tube video that wlked me through it...Took off back of dryer, then the top, then the front to get to the igniter...could not pull out the part, so I had to reach in and replace it while it was in the dryer. It Works!

The ordering and receiving of the part were wonderfully easy, but the construction of the lint filter left a lot to be desired. Bits of wire extended past the edge of the frame and drew blood when held, so had to trim the wire screen that extended past the frame. Also, the wire screen was not attached continuously around the frame and had to be clamped and glued. I did appreciate that the filter fit my machine.

The job is simple once you know how to remove the front panel. The steps are as follows:
1. disconnect the power cord.
2. remove 4 Phillips-head screws under the lip of the front panel that secure it to the top panel (#1 point Phillips-head screw driver)
3. swing the top panel up, it is hinged in the rear.
4. making note of the connection points of the color-coded wires, disconnect the wires to the lamp socket and door switch (I used a felt-tipped pen on the inside of the front panel to mark the connection points, "R" for red, etc.)
5. remove the upper 2 hex-head screws from inside of the front panel (5/16" nut-driver)
6. loosen the lower 2 hex-head screws (5/16" nut-driver) accessible from outside the panel (you only have to loosen them since the bottom mounting tabs are slotted)
7. slightly lift (to clear above mentioned lower tabs) and tilt the front panel toward you. Swing the front panel to the right as though you were opening a door and position so it does not fall.
8. remove 10 hex-head screws from the black lower rear access panel (5/16" nut-driver) and remove the broken drive belt. Note that the narrow black panel securing the power cable can remain in place.
9. at this point take advantage of the situation and vacuum out the years of lint and dust you could not reach before.
10. stand in front of the dryer, lift the dryer drum slightly and slip the new belt (rib side down) around the drum. Position the belt near the rear of the drum along the wear-mark left by the old belt.
11. go to the back and place the belt in the motor's drive-belt pulley, making sure the ribbed side of the belt mates with the ribs in the pulley.
12. position the tension wheel so that the it takes up the slack in the drive belt. Note the flat side of the drive belt will mate with the flat of the tension wheel.
13. spin the dryer drum a few turns by hand to make sure the drive belt lines up properly with the pulley.
14. reassemble the dryer by reversing the above steps, starting at step 8.

The repair for the average untrained mechanicslly inclined " first off google directions/instruction picture step by step " we took off the wrong part which made this job difficult there is a part on the back that was removed prior to guided directions, called parts select they are awesome"our belt was delivered the next day on a 3 day weekend I was suprised second correct part sent anyone who took on this job , they will appreciatte all this . the belt was fairly easy to repair just do as directed follow guidelines. difficulty detaching a part that never should be"pain in the a" order your part from this company they rock" and picture guide and specific direction guideline @ this dryer has well outlived the money spent still kicking strong after several years of use hotpoint dryer

disassembled chassis of dryer, unbolted top, lifted top to expose drum. bolted top back on. resumed repair next morning. unbolted top. lifted drum (it moved up and down about 1 inch) and got new belt around it. rebolted top down. tipped dryer to its back. unbolted and removed panel at bottom, exposing drive motor and tensioner spring. positioned belt around drive motor spindle and tensioner spring. replaced panel. reconnected dryer to electricity. reconnected gas using new flexible connector.