861-4730-090 General Electric Dryer - Instructions

This wan't a repair. It was simply a part replacement for a part that was easily accessable. I was more pleased at the fact that I could find the part considering how old the dryer is.

I called customer Servioce and they helped me with the corrfect part number

unknown
25 year old GE dryer started making strange scraping noises when running. This even when there were  no items in the appliance. Turning off the gas, and unplugging the power I disassembled the unit to find the nylon drum bushings worn down. Especially the felt like material under them that I think dissipates friction heat. A quick order to GD for the parts, 2 days later I had the part installed, and noise was gone.  

Kevin J. Reynolds.

drive belt gone, replaced belt and bearing

place inside of dryer

Pulled the old filter out of the door of the dryer and then removed the new filter from the shipping box and took the new Lint filter out of the packaging and then slipped the new lint filter into the lint filter holder and started up the dryer and away we went on our happy way. Thanks to all of you guys and gals at PARTS SELECT.

Took the old filter out and inserted the new filter which was a near perfect fit on a 36 year old dryed that is still kicking! Delivery of the part was less than 24 hours after ordering over the phone. Thanks1

First unscrew the two screws at top to disconnect the control panel. Lay unit on the back. Remove door(be careful not to lose washers and hinges). Remove four screws to lift off top. Wiggle drum, slip belt over drum. Replace door, then put Four screws back in place.Stand unit upright.Remove back panel, you should see belt hanging.Pulley wheel is in front of you.Follow instuctions sent with pulley wheel.Reattach you're ready to roll, make sure you sllip the belt on the drum until the drum spins.

We removed the lid to the dryer. The drum had to come out so the back access was removed and the belt taken off. The drum then slid out the front. The dryer had two elements both were broken. The new ones were stretched to the proper length and laced through the ceramic brackets. The new copper leads werre installed and the coils attached to them. We cleaned the dryer as much as possible and reassembled it. Works like a charm (for now)!

Removed Front of Machine, removed access panel on back of machine, reassembled after installing belt and cleaning out machine. Pretty Easy, hardest part is getting around the front of the drum.This machine has been going since 1978. 31 years, 2nd replacement belt and thats all, not bad, the washer that was bought at the same time went around 6 years ago, havent had the same luck, since then, two machines and the latest one is giving me problems already. They dont make them like they used to.

Finding parts for very old appliances (that otherwise are working great!) was very much appreciated...lint filters are very very important and this one has served it's useful life. Thank you for such an amazing parts inventory, good prices, and FAST delivery!

Used online instructions. Worked well.

Backwards to start- here's the correct way.Disconnect power and vent hose-tip onto front-remove bottom plate allowing access to bottom of dryer and the belt pulleys-remove the small plate in center and under that is a C-clip holding the drum shaft in place-remove the clip and washer-sit dryer upright - open the door and remove the 4 screws under the upper lip which hold the top of the dryer in place-lift up top and secure or have someone hold it up.-inside the top front on both sides are 2 screws per side and there are 2 screws at the bottom under the kick area, remove all 6 of these screws and the front of the dryer will come off-watch the wires-with the front off you can pull the drum forward to allow installing the new belt. - hold the new belt in place with a couple of pieces of tape-reverse the procedure to put drum back together and then thread the new belt onto the drive pulley and under the idler tension pulley.- reinstall back plate, vent hose, power and you're ready to go have a beer.

My husband and I had taken apart this dryer before, so the second time was a lot easier. The first time we took it apart it took 2-3 frustrating hours. So, if it's your first time, plan for longer.

1. Before we started anything we unplugged the dryer and disconnected the vent.
2. We removed the top and loosened the contol panel on top.
3. We removed the front. Be careful of the wires. You can label them, or just remember where they go.
4. Lay the dryer down on it's back. This make's it easier to remove the drum.
5. Remove the drum, but gently slide the belt off first. Don't stretch the belt removing it.
6. Once the drum was removed, we removed the screws from the inside of the drum.
7. We didn't need to use the entire kit, just the part that sits in the center and spins...kinda looks like a top. (Yes, that's my technical description)
8. We screwed in the new "top" and put the dryer back together.

Really the only part I had to help with (this time)was putting the drum back in to make sure it sat where it was supposed to. It made a big difference that it was laying on it's back...we didn't do that the first time, which was part of our frustration.

Putting the belt back on is a little tricky too. We had instructions still for our dryer to refer to put it back on. If you don't have yours, just google or bing for the instructions. There's website's out there with great pictures.

I got to supervise - my son did it for me!!!! Went very well!