DCCD330EDW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dennis from Crystal Falls, MI
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Squeaking when using dryer
It was simple to get drum out. I took all screws holding top and door out with out problems, then released the drive belt. It took some wiggling to get the drum out. I then was able to get at the rear elements. Taking the wires off the thermostat came off with a little persuasion. Removing shaft from drum took some stretching as I was doing the work by myself. I would suggest that a helper be used for the removal and replacement of the shaft. Reassembly was easy. Just reverse of the above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Bismarck, ND
- Parts Used:
- WE09X27634, WE03X37318
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
High Squeal Noise
The dryer made a loud squeal and I shut it off immediately.
1 - Unplug the dryer
2 - Took the top off and the front off the dryer
3 - Removed the 4 Front Dryer Drum Slides that were worn all the way through
4 - Pulled the bunched up Felt
5 - Vacuumed out the inside of the dryer -Very Important
6 - Put the drum slides in and felt piece
7 - Put the front on top back on
8 - Worked great
1 - Unplug the dryer
2 - Took the top off and the front off the dryer
3 - Removed the 4 Front Dryer Drum Slides that were worn all the way through
4 - Pulled the bunched up Felt
5 - Vacuumed out the inside of the dryer -Very Important
6 - Put the drum slides in and felt piece
7 - Put the front on top back on
8 - Worked great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GUY from BEDFORD HILLS, NY
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drum slide wore - damaged drum bearing
r/r parts unit runs great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Hendersonville, TN
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud squeaking noise
Repair was VERY easy - 4 screws total! Used google to find a video online that showed the steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremy from Wexford, PA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud squeaking sound from dryer drum.
Initially purchased just the plastic slides, but when I opened the dryer I found the top drum bearing was smashed and the plastic was basically gone in a whole section, so I then ended up ordering the bearing as well. If you hear the loud squeaking, just buy the top drum bearing and the 4 slides (two white and two dark green). It is an easy repair and the squeaking sound is gone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Sterling Heights, MI
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
worn dryer drum slides
i first popped off the top of te dryer after removing the two screws in frotn when you open the door. I then removed the two screws holding the front together. after tilting the front out i was able to place the slides in without having to pull of the front entirely.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CARLOS from SANTA FE, NM
- Parts Used:
- WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud squeel
removed two phillips screws from front panel, removed front panel and raised top cover, had my wife hold up top cover while i removed belt and installed new one, reassembled in reverse order, turned on dryer and checked for proper operation, and yes i did unplug the unit. worked great!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from Redondo Beach, CA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
drum wore down plastic
pulled off the top, pulled off the front then replaced the plastic that was supporting the front side of the drum. fairly easy to replace although the little plastic 'slides' (you need 4 of them)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONNA from PLEASANT CITY, OH
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
loud screaching noise
We removed the top of the the dryer and then removed the front part. Then put the traps in place, put the other parts of the dryer back on, and turned the dryer back on. Just as simple as that. No extra fees.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from santa maria, CA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
squeaking
snap in snap out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from Westfield, NC
- Parts Used:
- WE09X27634
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Squeaking Dryer
The top and front of the dryer had to come off, and taking off the top (and later putting it back on) was the hardest part. The old seal was stretched approximately two feet longer than the replacement part, and its thinness caused the drum to squeak as it scraped by the door panel. We simply pressed the new seal into place after pulling out the old one. Piece of cake. Putting the front of the dryer back on was simple as well. Fitting the top back into its slots properly was the biggest pain of the whole ordeal. The part came in about 2 days. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Big Rapids, MI
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bearing and slides worn out
took off top of dryer, took out 2 screws so front of dryer could be removed, replaced bearing,slides and felt seal
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Fort Washington, PA
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Squeeky Noise When Dryer Was Running
First I removed the 2 screws that hold the lid down. Then I pulled the lid off. Then I removed the 2 screws that hold the front of the dryer in place. Then I lifted the drum a little and pulled the front cabinet out a little so I could see the drum slides. I removed the bad drum slides and installed the new ones. I then put everything back together and turned on the dryer. The squeeky noise was gone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Saint Louis, MO
- Parts Used:
- WE09X27634
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Squeaky dryer
4 screws, that was it
open the dryer door, locate the 2 screws that hold the top in place, unscrew them
then locate the 2 screws (located near the top of the dryer (facing toward you) and unscrew them
allow the front of the dryer to tilit out towards you, replace the felt, slide the drum back into place into the front of the dryer, resecure the 2 screws (removed last)
lower top of dryer back in place, being careful to make sure the top clips back in correctly.
re-install the 2 screws that secure the dryer top to the front.
boom, you are done....
Amazingly easy work...
open the dryer door, locate the 2 screws that hold the top in place, unscrew them
then locate the 2 screws (located near the top of the dryer (facing toward you) and unscrew them
allow the front of the dryer to tilit out towards you, replace the felt, slide the drum back into place into the front of the dryer, resecure the 2 screws (removed last)
lower top of dryer back in place, being careful to make sure the top clips back in correctly.
re-install the 2 screws that secure the dryer top to the front.
boom, you are done....
Amazingly easy work...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from early branch, SC
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
clip on door broke
it was easy, it clip right on.needed to give it a little tap to get it in .
Was this instruction helpful to you?
Thank you for voting!