DDE5140UBLWH General Electric Dryer - Instructions

Checked out problem found belt broke and order part from part select and when it got in I replaced the belt and then found pully bad too. so I order that part from ya'll and it tok less than 5 mint to install. everything went very well and I and my wife are very happy with everything.
Thank's Partselect,
John& Roxanna

Removed old lint filter and replaced with new one. Was impressed with the fast delivery.

unplugged dryer,removed air duct,,remove( top of dryer) by removing the two back screws.... removed two screws under (fornt top lid),laid top to the side. ...Now remove ( front of dryer) remove,two screws near the( top on the inside)...lean dryer back, and remove outsidescrews at the bottom)..the front should come off. ..located small square opening in the back of the dryer release clamp from drum ,...put belt around drum... put drum and dryer back together...(relace any electrical wires removed if any..remove (rear bottom plug panel)..you can now see the lower inside of dryer....make sure belt is level on drum by rotating...place belt on lower pully,... lift tension(spring pully) on to belt.. replace cover..

The job is simple once you know how to remove the front panel. The steps are as follows:
1. disconnect the power cord.
2. remove 4 Phillips-head screws under the lip of the front panel that secure it to the top panel (#1 point Phillips-head screw driver)
3. swing the top panel up, it is hinged in the rear.
4. making note of the connection points of the color-coded wires, disconnect the wires to the lamp socket and door switch (I used a felt-tipped pen on the inside of the front panel to mark the connection points, "R" for red, etc.)
5. remove the upper 2 hex-head screws from inside of the front panel (5/16" nut-driver)
6. loosen the lower 2 hex-head screws (5/16" nut-driver) accessible from outside the panel (you only have to loosen them since the bottom mounting tabs are slotted)
7. slightly lift (to clear above mentioned lower tabs) and tilt the front panel toward you. Swing the front panel to the right as though you were opening a door and position so it does not fall.
8. remove 10 hex-head screws from the black lower rear access panel (5/16" nut-driver) and remove the broken drive belt. Note that the narrow black panel securing the power cable can remain in place.
9. at this point take advantage of the situation and vacuum out the years of lint and dust you could not reach before.
10. stand in front of the dryer, lift the dryer drum slightly and slip the new belt (rib side down) around the drum. Position the belt near the rear of the drum along the wear-mark left by the old belt.
11. go to the back and place the belt in the motor's drive-belt pulley, making sure the ribbed side of the belt mates with the ribs in the pulley.
12. position the tension wheel so that the it takes up the slack in the drive belt. Note the flat side of the drive belt will mate with the flat of the tension wheel.
13. spin the dryer drum a few turns by hand to make sure the drive belt lines up properly with the pulley.
14. reassemble the dryer by reversing the above steps, starting at step 8.

The repair for the average untrained mechanicslly inclined " first off google directions/instruction picture step by step " we took off the wrong part which made this job difficult there is a part on the back that was removed prior to guided directions, called parts select they are awesome"our belt was delivered the next day on a 3 day weekend I was suprised second correct part sent anyone who took on this job , they will appreciatte all this . the belt was fairly easy to repair just do as directed follow guidelines. difficulty detaching a part that never should be"pain in the a" order your part from this company they rock" and picture guide and specific direction guideline @ this dryer has well outlived the money spent still kicking strong after several years of use hotpoint dryer

I suspected the idler pulley shaft was worn. I found the repalcement pulley on parts select web site. finding the part was very easy and delivery was very quick. After removing the dryer from the wall,I removed the access panel in the rear which exposed the motor, belt, and pulley. After removing the belt from the pulley, I removed the pully assembly from the dryer. I removed the keeper retaining ring on the pulley and installed the new pulley with the new parts supplied. The new pulley assembly was then ready for re-installation.

The ordering and receiving of the part were wonderfully easy, but the construction of the lint filter left a lot to be desired. Bits of wire extended past the edge of the frame and drew blood when held, so had to trim the wire screen that extended past the frame. Also, the wire screen was not attached continuously around the frame and had to be clamped and glued. I did appreciate that the filter fit my machine.

take off door, take off front, mind the 2 wires for the door switch, take off top, take out enough screws on right side so it will lean out a bit for the drum to be removed. before removing drum you must remove the belt. pull the wheel to the right, minding the belt pattern for reassembly, its springy and will relieve tension. pull drum out. look to the left of the pulley and check to see any stray wire that may have pulled out while battling the belt. if you found a stray wire and it reaches the dryer motor find its home. on to the coils. I left assembly on dryer so I didn't have to figure out wire placement. the end connectors that the coils attach to are to be reused so don't get to mean with them. remove the end connectors minding how many wires it has and which of the 2 coils go to it. remove the old coils so as not to damage the very brittle ceramic insulators. on to the new, the instructions will tell you to stretch out the new coils to specified lengths. start with the shorter one first! just to see the stretchiness and how far is too far to stretch, if to long it will touch the heat shield and no good can come of that. after stretched out its time to string new coils in, carefully, so as not to stretch or collapse the coil. now hooking the end connectors to the ends of spring. I used 2 pliers to bend the tab a little bigger so it would cover the spring end. after springs are attached to ends and ends are in place, time to battle the drum and tensioner again, make sure plastic piece is on drum insert if equipped, put drum in place and bend tensioner down and install belt. put side screws on, then front and 2 wires , then top then door. plug in and start up. if unit doesn't start remember that stray wire going to the motor, you guessed it wire goes to the start switch. unplug and hook up the wire and it will work.

I didn't know what was wrong at first, only that the dryer would not start. I bought it used so had no fear of taking it apart to diagnose. Found the broken belt inside, ordered a replacement, installed the new belt, then crossed my fingers. Was pleasantly surprised that was all that was wrong and that for less than $20, including shipping, a few hours of my time, and a little help from YouTube videos the dryer is working again!

disassembled chassis of dryer, unbolted top, lifted top to expose drum. bolted top back on. resumed repair next morning. unbolted top. lifted drum (it moved up and down about 1 inch) and got new belt around it. rebolted top down. tipped dryer to its back. unbolted and removed panel at bottom, exposing drive motor and tensioner spring. positioned belt around drive motor spindle and tensioner spring. replaced panel. reconnected dryer to electricity. reconnected gas using new flexible connector.

Researching on the web I thought the trouble might be lint buildup or trouble w/ one of the parts involved in spinning the drum. However I cleaned out all the lint and replaced the belt and idler pulley and this didn't improve the smell (drum bearing was fine). I then concluded the trouble was the motor. Running the motor w/o the drum in place confirmed this was where the noise/smell was coming from. Replacing the motor was fiddly--I had to remove the clip holding the motor (pried the top w/ a screwdriver), wires (made a diagram so as to put back in same order, they were hard to get off--a pliers did the job), clamps holding the motor on the duct, the motor mount, the duct, the fan. Putting all this back together took a while (not hard just fiddly). Tested the motor w/out the drum in place and it sounded fine. Put the drum and back/front/top panels back and the dryer runs fine now. All parts came quickly and exactly matched the parts in my 1993 Hotpoint dryer. As others have said the pulley kit is not needed--these are included w/ the motor. BTW I am a 53-year-old lady. Thanks to all who took the time to write up their experiences--big help!!

I did not have an actual repair. I simply replaced the lint filter that dropped into the receptacle. However, what I want to mention is that the part was available as old as the dryer is and there was a nice photo to scale of the replacement part so that I was sure I was getting the correct piece. A great site to obtain parts from my experience.

Just replaced it with the new one

I only ordered a lint filter with frame but wanted to let other's know that ordering from your site was extremely easy and the shipping was extremely fast!! I received my order with 2 days of placing my order. Thank you!!

Deftly removed the old lint trap and placed the new frame in place. It worked perfectly. Hands only repair.