DSKS333EC0WW General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brandon from Jonesboro, AR
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer knob broke
Took it out of the package. Slid in it in place, took less than two minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Stockton, CA
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken timer knob
Knob fit perfect. Simple pull off and put new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teddy from Norwalk, CT
- Parts Used:
- WE22X35337
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The lent filter protector broke
removed broken part and replaced it altogether.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne from Marblehead, MA
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The time knob had broken and come off
Our repair was super easy. All we had to do was line the new Timer Knob up with the knob on the dryer and slip it on. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Oregon, OH
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Loud Squeek When Started until warmed-up
Ordered the recommended parts on-line and they showed up the next day. I followed the on-line repair video that described it all step-by-step.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard A. from Little Elm, TX
- Parts Used:
- WD21X10261
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dishwasher would not start
Took the back off/there were six phillips head screws. Took the protective cover off the Interlock Switches and found the problem. One of the buttons was jambed and would not move. I pulled the switch up and pulled the connecting wires. This took a little bit of doing as the connectors have been set for over 8 years. I used a pair of needle nose pliers. I reconnected the new switch and punched both switches and the washer started. It was an easy repair after that, putting everything back in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Riverview, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The unit would not start.
First I turned off the breaker to the dishwasher. I then removed the bolts that held on the inner cover(note the two small bolts go on the bottom one on each side). I lifted the switch up and disconnected the wire clips from each side. I then put the new switch in place with the wires attached. Then replaced the cover and screwed it into place. Closed the door and flipped the breaker back on and turned the dish washer on and it started up. A very easy replaceable part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JoAnn from Daytona Beach, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Would Not Start
Put part in. Put the door cover on & turned on & it worked. Thanks for having the part. So far, so good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dee from San Saba, TX
- Parts Used:
- WE1X1263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer would not turn on
took the old part off @ put the new one on. Took about 5 sec.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janet from martinsville, IN
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer did not latch
easy to fix took less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fawn from Loganville, GA
- Parts Used:
- WE1M1011
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door would no longer shut.
Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from San Francisco, CA
- Parts Used:
- WE22X35337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grid Slide -3 plactic nubs broken slide was loose.
Take old grid slide and pannel off. Clean lint trap wire framework and replace. Make sure this trap frame fits snug against the door, otherwise it puts pressure on the new slide. This is the second time I have replaced this Grid Slide. Slid new pannel into grid frame. Ready to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis G from Naples, FL
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Holes were not threaded on rear bearing kit
Had to tap three holes in the rear bearing to match the three attachment screws. Screw up with the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from early branch, SC
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
clip on door broke
it was easy, it clip right on.needed to give it a little tap to get it in .
Was this instruction helpful to you?
Thank you for voting!