DPSB620ECW General Electric Dryer - Instructions

Pulled out the remnants of the old latch out with the pliers and then popped the new one in...less than 2 minutes. Oh, and the part was delivered in less than 2 days. Great job, Partselect !

It makes it real easy if you have two people!! Put the dryer on it back--You'll need to protect the floor and the warm air exhaust of the dryer.
Remove the two screws that secure the top--they are located on the inside upper portion of where the door seats on the front panel. Remove the top
Remove the front by removing two screws near the top--one on each side
Remove the belt from the idler pulley--note how it comes off
Lift drum out of dryer
Use the torx bit to remove the bearing
If you got the kit it comes w/ the bearing housing--you'll need to disconnect a couple of the wiring harnesses holding the heater--replace the bearing housing
This is the perfect time to remove all dust bunnies
Re-install everything in reverse order

Removed two screws on dryer top and removed top, removed two screws holding front of cabinet and removed cabinet front to the side, disconnected wires to door switch, removed two bolts from motor mount bracket, pulled motor back to access blower wheel, removed old wheel and installed new one, reversed steps, unscrewed old light bulb and screwed in new one.

Had pure hell getting to drum belt and putting it back onto motor pulley and idler, cussed a little, didn't really help . replaced front of cabinet and top, did test run all worked ok.

This job was a little difficult, espicially accessing the belt and idler pulley...

my problem was easy, i orderd a new lint filter, for a
dryer that is at least 10y/o. it came to me by FEDEX,
in 3 days. i threw out the old one and put in the new
one. easy peasy. i will say that this website had what i
wanted and got it to me very quickly. good job by
PARTSELECT......

The diagrams on the Parts Select web site is what made it easy for me. I could see from the diagram how the dryer was assembled. I removed the two screws holding the top on then separated the front apart from the drum. I did have to remove the panel in the back where the power connects to access the drive pulley and belt tensioner. I slid the old belt off and simply reversed the procedure for the new one. Put it back together and it runs beautifully.

I also installed a new door gasket with no tools. Now it does not leak lint from the fronf door.

When I went home at Christmas, I saw that my Mom had been using a small bench to keep her dryer door shut. I wrote the make / model of the dryer down and found your website. I ordered the part, and my sister snapped it into place. My mom was so happy to have her dryer door stay shut again!

I took off the top panel and ran the dryer. I watched as the drum turned more and more slowly until it stopped. I turned it off, and unplugged it.
I took off the front panel, simply swinging it to the left like a gate so I didn't have to disconnect any wires, then pulled out the drum. I should have taken the belt off the pulley idler first!
Got the drum out and could see the broken idler wheel and the groove on the drum's back post for the O-ring. There is a silicon sheath that goes on this back post - don't lose it if it is still good or you'll have to buy another.
Getting the idler wheel off the stem was as simple as using the pliers to turn the nut until it came off. I put the new one on, then put the nut back on. I adjusted the position of the idler pulley so that the belt would not be out of line with the pulley on the motor - I just eye-balled it.
I slipped the belt around the drum, put the silicon sheath back on the drum post, then put the o-ring in the groove on the post.
Put the drum back in the dryer, lining up the post to go back in the hole was a challenge.
Then, getting the belt back on the pulley needed a little muscle to apply the tension needed to allow the belt to get into place. I had one hand in each opening on each side of the drum and did it by feel.
I put the front panel back on and did a test run. The drum was turning with force now, not slowing down nor easy to stop by applying resistance with my hand. It was also much quieter.
Put on the top panel and done!

Removed case parts to expose internal wiring. Vacuumed up various types of mouse debris and plugged hole they were using. Ordered terminal block to replace the one that melted while sparks were flying. Replaced power cord with one I had in my basement from some other appliance that died a while ago. "Hey honey, ya know those old parts I saved..." :) Now it is heating to capacity and no spark-show! Oh yeah, the part I ordered from Partselect.com was delivered to my door the next day!!!!! Wow!

1st - removed the two screws inside the front door panel. They are somewhat hidden up underneath so you may have to look for them. 2nd - I removed the top of the dryer cabinet by lifting it out of the clips holding it in place. 3rd - removed the two screws (one on each side) in the o=uppper corner of where the side panels connect the front panel. These are about 3/4" phillips head screws. Then the front panel could be moved to one side of the dry. 4th - remove the drum by lifting it up and out the open top area. 5th - add the new belt to the dryer tub (rib side towards the drum) and replace dryer tub to its original position. 6th - reaching in underneath the tub you need to pull the ideler pulley toward the center of the cabinet while laying the belt on the "outer side" of the ideler pulley and at the same time fitting the belt over the small pulley located on the motor. Once that is done, you reassemble in reverse order and should be good to go.

--Removed bottom rear panel (right under where 220 line comes in) which exposed belt and idler pulley.
--Relieved tension on belt by moving idler arm and moved belt off idler puller (just to the side).
--Removed e-clip.
--Removed old pulley and washers.
--Installed new thick plastic washer first, then pulley, then e-clip.
--Relieve tension and place belt back on new pulley.
--Replace back panel.
-Fini!

I was cleaning my laundry room when I noticed the gasket needed cleaning. While wiping it off it appeared as though I could remove it and that was my biggest mistake. Once removed it could not be replaced, due to the little parts that held it to the door began tearing off as I tried to put it back on. I ordered a new gasket and had it put on. It did not require any tools, just concentration. I've learned "if it's not broken, don't fix it"! I spoke with several other people and I am the only one who has removed a gasket. Thank you very much PartSelect for your help.

Used an allen wrench to remove the heat deflector and used allen wrench to replace it with the new one. HINT!! Do not lean on the inside of the dryer!!!!!!

took out broken filter and replaced with new lint
filter.

I had to remove all screws from the back of the dryer, control panel, and one side. Pulled top off. Took out two screws that held front door panel on. Disconnected 3 wires into door and completely removed door panel. Disconneted pink wire from heating element then slide belt off drum as I removed the drum. Pulled off the old completly worn out drum bearing sleeve and replaced it. Replaced drum slides as some were worn through. Had a little trouble getting belt back on when I reconnected everything but for 50 dollars in parts and shipping I have working dryer, so I would say it was well worth the effort.

took two screws off the front. They were behind the door. These screws held the top on. Lifted top off and took two screws from the frame holding the front door and panel on. Disconnected three wires and removed front panel. Laid dryer over on right side and removed four screws from bottom and back,two from control panel and removed left side.lifted drum out and removed belt. Removed nut cap and idler pulley wheel. Replaced same. removed three screws holding screen and rear drum bearing to drum. Replaced same. Removed electric heat coils from back and removed receiver for rear drum bearing. Replaced same. Put everything back in reverse order. Works better than new!!