DCVH515GFG General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Austell, GA
- Parts Used:
- WE04X25996
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Igniter burnt out
The bracket on the part supplied was different than the original. The wire connector was also different. The bracket had to be drilled for a hole to match the original. The connector had to be cut off and the wires soldered together, then tied off to the frame to keep them away from the flame. The repair works like new but not the simple plug and play I was expecting. In all fairness the exact model number was not available, probably since the appliance was 24 years old, so I chose the closest model number with the picture that looked like what I had. Problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Rochester, NY
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Drum was squeaking and making a lot of noise!
Took apart the dryer housing fairly quickly, pulled out the drum, and installed the kit. Was fairly simple. Then reassembled. The hardest part was trying to get the belt on properly and reconnect to the motor. Believe it or not, I wasted most of my time on the belt. Should've watched the video better and listened to my wife and her suggestions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from WACO, TX
- Parts Used:
- WE2M302
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Reversing the dryer door.
Removed 4 #1 Philips screws from 1side and add to the other side.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from CORP CHRISTI, TX
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
BELT SQUEAKING
TOOK OFF TOP AND FRONT PANEL REACHED IN UNDER TUBE AND REMOVED FROM BELT TENSIONER HARDEST PART IS PUTTING BACK ON TENSIONER TAKES TWO HANDS LAYING ON YOUR BELLY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Sugar Valley, GA
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
dryer had a loud sqeaking noise
removed top, 2 hex screws, removed front 2 hex screws & 2 star screws. removed belt, slid drum out. Removed old bearing and replaced with new bearing kit. assembled in reverse.
It would help to have another person assist you.
It would help to have another person assist you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelly from MURFREESBORO, TN
- Parts Used:
- WE25M40
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Squeaky dryer
I followed the YouTube video and it gave me step by step instructions however I really needed to replace my dryer slides to fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Laurel Springs, NJ
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
dryer belt snapped
Replaced it as one would. I took off the front facing and replaced the belt. It took a bit of searching to find the proper way to route the belt around the pulley.
It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.
If I were to do it again, it would take 30 minutes or less.
It took a while since it was my first time and I wasn't sure what to take apart and what to leave intact.
If I were to do it again, it would take 30 minutes or less.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phuc from WOODBRIDGE, VA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
drive belt is broken.
Follow the instructions from YOUTUBE to replace the new drive belt..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from EPHRATA, PA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
Dryer needed a new dryer belt
I followed the directions I found on my tablet on youtube.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Freeland, MI
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
loud noise when ran for 5 min.
Replaced the rear drum bearing. Not doing it before ,it took about 1 1/2 hrs. Problem was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Westminster, MD
- Parts Used:
- WE25M40, WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
clothes being eaten first then the loud noise
I replaced front and rear bearing.The rear I replaced because of cause and effect.There was some play so I am glad I replaced the rear too. Make sure you order drum slides. Ken
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff D from NEW MEADOWS, ID
- Parts Used:
- WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Drum would not turn
Exactly how your perfect video instructions showed me. Thank you for a job well done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from SICKLERVILLE, NJ
- Parts Used:
- WE03X37317, WE14M124, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
There was screeching noise during the drying cycle. Clothes being dried were getting stuck in the upper bearing.
I followed the instructions given in the video I watched when ordering the parts. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from EASTON, CT
- Parts Used:
- WE12X83
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
Replace broken drum belt and belt idler pully wheel.
Watched video instruction, paying attention to what it showed in machine. Several virsions of similar designs over the years, look over yours and note access points, take pictures as you go! Just pay attention, it is very logical. Spread the side panels to get the drum in and out, and pay attention to drum axel in back and the bushing it rides in. Be patient, be firm but gentle, no real forcing needed if you are alligned. Be sure the grooves of belt are on the drum, drive wheel on motor, no twists. Reverse order to reassemble. There are several internet videos of models with same basic setup, so look at others if one doesn't show the detail you need to see, or clear some uncertainty. Your local hardware to sorce push fastening for the idler wheel to shaft if you mash it up, they are cheep and several styles will work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacqueline from FARMINGTON, ME
- Parts Used:
- WE05X20431, WE09X27634, WE03X37317, WE14M124, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The felt seal came out, and drum slides were cracked
We watched the YouTUbe video of Steve from this site and followed his instructions for how to replace the top bearing on the dryer, and the seal. It went quickly and easily, and his instructions were perfect. It helped that the model in the video matched ours almost exactly.
Was this instruction helpful to you?
Thank you for voting!