UAN7303-80A Frigidaire Dryer - Instructions

i watched the video that is furnished at parts select, it was very useful in doing this repair. i would strongly recommend watching this as i did install the ground bearing wrong to start with,and restringing the drum belt is something you have to feel as your installing it back in place so the video is useful for that as well. my repair was on a front load dryer made by Frigidaire,

Replaced rear bearing on back of dryer. Repair cost $20.00 an a little time. Much better then buying a new dryer. It was easy to repair the video instructions were great. I would do it again it needed.

I used the video, and it helped me a lot! I got the drum out, installed the new bearing, greased the new shaft and the receptacle, then I reassembled. When I tested it, mine was still very noisy, so I removed the drum once more and cleaned/added some grease on the tensioner bearing. This was the cause of the noise in my case, but the bearing & housing were nearly shot, so something would have given out very soon. I would suggest to grease the tensioner the first time to save time and effort. (And save some of the grease for the tensioner pulley). SAFETY TIP: there was also a ton of lint that got trapped inside the unit!!! Clean your dryer once per year to prevent it becoming a fire trap!

I ordered the rear drum assembly on Monday evening and the part came on Wed at 11 am. I started the repair at 1 and finished at 3. It would have been faster, but my computer kept freezing during the repair video. The video was so easy to follow. I could have used longer arms or a helper, but I managed to get the job done by myself. Needless to say, my husband was thrilled. Great service. Thanks

The repair video from PartSelect.com was excellent in describing how to fix the dryer. All of the parts were included in the replacement kit, including the screws and ball bearing. I was very impressed with the quality of the kit and the video. A $25 kit probably saved me hundreds in repair cost and saved me from having to buy another dryer. Here's to another 14 years of use!

Ordered the part from PartSelect.com. It came in a couple of days, which was nice. My wife was all over me to fix the dryer, or buy a new one. Needless to say, I didn't think the old one was done. The bearing assembly had an instructional video. This provided easy to follow instructions, and simple advice even I could follow. Everything went well, and the dryer is now quietly running as good as new. Awesome website, and the customer service is excellant too. WE use PartSelect.com at work all the time. Im a property manager, and the parts and advice save us thousands every year. Thanks guys!

when the bearing broke the drum fell in the back. I tore the dryer apart, ordered the part and fixed it when the part came. the dryer runs like new now!

Repair went just according to the video except to pull the drum out there was a plastic lock at the front of the dryer. It was held in by one screw and easy to take off. When I pulled the drum out the armature and spring that hold the belt tight fell off. I panicked a little, but easily put the pieces back in place. When I started the dryer for the first time it sounded odd but realized it was the sound of all the grease spreading itself around the bearing.

Had the macnine apart before ordering the Bearing Assembly. Reading other comments convinced me to order the Bearing Assembly. Parts were shipped very quickly after ordering and following the instructions on the web site things went back together easily.

Found instructions on "UTube"some of the screws were in a different position but you can see them. While you have the dryer apart it's a great time to clean it and also as long as you've gone this far replace the belt,it's probably time.

took front panel off, removed access panel in rear to disconnect the belt from motor. removed top panel (this is a stack unit) take plastic rivets loose from lint trap, remove lint trap tube, pull drum out after slightly pulling up to dislodge drum from bearing cradle, Remove bracket and bearing from back of unit, clean parts of old grease (be carefull not to loose small ball bearing on back) Reassemble parts using moderate amount of new grease, put parts back together in reverse order.

The consensus seemed to be that the loud squealing was most likely the rear drum bearing needing to be replaced. Although the repair went very well (great video!), it did not fix the problem. BEFORE you go the route of replacing the rear bearing, first pop up the top and see if a little piece of plastic that is attached to the top middle of the front panel by a screw is rubbing against the drum (you have to have a load going). I removed this part (I could not find it listed on any parts list) and the squealing stopped. I have no idea what the purpose of this part is, except for maybe keeping the drum from dropping too far down if the load is really unbalanced. This plastic part is on the dryer that has the controls on the front (it has the ability to be stackable) and might not be on the other unit that has the controls on the top back. If anyone has posted this as a possible cause of the squealing, I haven't seen it.

First I like fixing things for myself. So I looked the problem up on the internet. Found the repair tech that I needed. The found your parts site. And BOOM. Looked up mt part on your site. Very easy you had everything I needed. And you got it to me quick. THANKS. When the part hit my mailbox. Everything I needed was there. I pulled the plug. Fliped the lid up. Took off the front. Removed belt off the ideler. Removed drum replaced bearing assy. Put it back together. Closed the lid and pluged the unit in. Worked so well I felt like a pro. My wife was tickled pink. Just like a new one. Thanks guys for making me look good and saving me a lot of money. Will use this site again. I give you 2 thumbs up.