DE700EDH1 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cindy from Mauston, WI
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Loud squeeking when ran
Followed online video. All went smooth. Runs great!!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Aurora, IL
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set, Wrench (Adjustable)
Drum Squeeking
Replace the Drum Bearing and Shaft
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gale from Portland, OR
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Loud squealing
Taking it apart was no problem other than having to remove solidified grease in order to remove bearing. Also I found it easier to remove belt by removing screws holding drum in place first. Putting it back together was more involved. Taping metal strip to back with scotch tape made putting in new bracket a breeze. Tipping dryer on its' back was the only way I could get the screw holes to line up when installing the drum. Removing the vent cover, and installing from the back, made re-installing the belt tensioner much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from edinboro, PA
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
loud scratchy noise
first and foremost, watching video on replacement/repair was key to success.furthermore, i ordered part one day and was at my doorstep the following day. the installation process took approximately half of an hour which included vaccuuming cabinet of lint.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- scott from whitehouse station, NJ
- Parts Used:
- 5303281153, 131825900
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Machine was making a squeaking noise.
Followed video instructions that were emailed by you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Bells, TN
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Loud squeeling noise
I had trouble with the little piece on the back side of the dryer not lining up with the bearing housing. I also didn't see how the drum was gonna stay in place but finally realized the front cover lines it up. All in all it was awesome to get the part I needed so quickly and cheap, thanks a lot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from Hartford, CT
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No Power to the Oven
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Lampasas, TX
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Control will not work - only clock blinks
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamison from clayton, GA
- Parts Used:
- 5303281153, 131825900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The drum was out of balance
I removed the panel's that enclosed the drum, removed the drum and cleaned all the lint around the drum, heat panel, drive motor, and switch's.
removed the old support bearing and grounding ball then applied grease into the new support hub and reinstalled the new hub and grounding ball and then reassembled the dryer. Runs like it was new.
removed the old support bearing and grounding ball then applied grease into the new support hub and reinstalled the new hub and grounding ball and then reassembled the dryer. Runs like it was new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from cherry hill, NJ
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
rear bearing failure
after cutting the power, I used a putty knife to release the two holding clips ot remove the top,, 2 foward facing screws on either side of the front and two cap covered screws holding the bottom and unhooked the two electricial connections for the control panel and removed the front panel. Since this was a stack unit and in a closet most work had to be done from the front. By reaching inside to remove the belt from the motor,removing the drum was the easy part, to get to the bearing, but unfortunatly I had to remove the dryer from the closet to replace the back bearing clip and ball. After that replacing the bearing bracket and housing it was a breeze. Getting the unit back in the closet was a slight struggle, but it all worked out for the best got a chance to cleas behind the dryer, and the repaire was successful, phew.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Bartow, WV
- Parts Used:
- 5303281153, 131825900, 5303281153, 131724301
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
we heard the most deafening screech! when we investigated we found that the plastic part that the shaft rested in was worn, unevenly and the shaft end was scored. (we live in a house with 8 people so a fast fix was needed) I looked up the part on a sears site. when I checked the part avalibility I f
we removed the top of the dryer which was clipped on. then removed the front, including the door, being careful to unhook the electrical elements. then we removed the screws that attached the dryer drum to the back of the shaft. then we took the shaft out of the bracket. then we removed the plate from the back of the dryer that held the ball, the bearing and the bracket together. then we waited for parts and thanked God that the weather was fair so we could hang our clean clothes out!!! the parts came ahead of the rain so it was reverse order. then try the dryer!!!fantastic!! to qoute my kids "you rock"
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from New York, NY
- Parts Used:
- 5308015435
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The knob of my dryer broke
I had a repair man fix it- it went very well
Was this instruction helpful to you?
Thank you for voting!
they where just wore out.
Taking off front of and top of dryer and panels on the back. Releasing the belt and taking out the tube un screwing the two pieces off the back of the machine putting new ones in and putting belt back around drum and setting drum in. Then holding drum while the front is put back on then attach top and a couple panels on the back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryant from tolna, ND
- Parts Used:
- 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer did not turn
put the new part on with ease took 5 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Mont Pelier, VT
- Parts Used:
- 5303281153, 5303281153, 131825900, 5303281153, 131724301
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
rear support bearing squeeking
removed top and front of machine. removed drum. replaced shaft, bearing bracket, and support bearing from inside. replaced grrounding ball and clip from outside. reassemble.
this should be available as a kit, and should include high temp grease to put in bearing bracket
this should be available as a kit, and should include high temp grease to put in bearing bracket
Was this instruction helpful to you?
Thank you for voting!