FER221AS0 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- TJ from SCOTT DEPOT, WV
- Parts Used:
- 131658800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door catch broken
Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from little Egg Harbour, NJ
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Lound noise inside dryer
1. unplug the dryer, remove the aluminum vent and move it to an area that has a lot of elbow room.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Brandon, MS
- Parts Used:
- 131553900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Heating element went out
Our heating element went out on our Frigidaire Affinity dryer. My husband is good at repairing things so we decided to order the part and do the repairs rather than hire a service technician. Before looking at the dryer we thought the back could be unscrewed and taken off to give access to the element but it did not. He had to take the dryer drum out to access the element. It was easy enough for him to do though and since we had everything opened up I was able to use the shop vac to get all lint cleaned out. I'm glad he did have to take the drum out after I realized the gasket on the exhaust pipe wasn't fitted on properly. There was some lint where there should not have been. Now that everything is clean and we have the new heating element installed we are good to go! The whole process of taking apart, installation and putting back together took about an hour and 15 minutes so not bad and we only had to pay for the part and shipping! Thanks PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hua from San Diego, CA
- Parts Used:
- 5303937139, 5303283286
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Dryer kept eating clothes
Took apart the dryer, definitely a two person job. Cleaned up a bag full of lint that collected in the dryer (can't believe it didn't start a fire!), removed the old glides and seals, sandpapered off the old adhesive, applied fresh adhesive, attached the glide and seals, waited for the adhesive to dry, reassembled the dryer. Now it's working like a charm!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from COVINGTON, KY
- Parts Used:
- 134120900
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dryer not heating
UNPLUG DRYER (this is key) Removed the top of dryer. used screwdriver and pliers to remove two screws and electrical connections then reinstalled new part stick the magnet behind the part to the back of the dryer to help control the small screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from CRANBURY, NJ
- Parts Used:
- 134120900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
May not have to take out the whole drum to replace the limiter!
After lifting the dryer top and finding the location of the thermal limiter on the back of the dryer, where it is difficult to get at, I carefully cut through the dryer cabinet with the multimaster on three sides to form a 'flap' upon which the limiter was mounted. By prying this flap open from the back, the two wires and two screws are easily accessible to replace the limiter, without having to remove the whole drum. Afterwards, I just bent the flap back into place and taped the seams. If it ever blows again, the fix will take all of about two minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Weston, FL
- Parts Used:
- 131858004
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water temperature knob broke
I push the new knob onto the post that fit the knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara J. from Lancaster, CA
- Parts Used:
- 131450300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint filter was wearing out.
Just replaced the new lint filter with the old lint filter. The part fit perfectly. I did not have a problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Mentor, OH
- Parts Used:
- 131644700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door handle broke and came off.
Simply popped it back into place, careful not to break the new handle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Rome, NY
- Parts Used:
- 131622202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
It got lost...
It was very, very simple... I just had to find two screws ( that were not included)...no problem...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrance from MENOMONIE, WI
- Parts Used:
- 131644700
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No problem
Just snap into place
Was this instruction helpful to you?
Thank you for voting!
Both knobs were broken
Ordered knobs on Monday early. Received midday Tuesday! Very fast delivery. Knobs fit perfectly, no tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from HGHLNDS RANCH, CO
- Parts Used:
- 131553900
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
dryer heat did not work
The how to video was great. I had a little problem with getting the belt back on the pulleys. Not enough room for my hands. I did manage to get it back on ,and runs great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANK from VERO BEACH, FL
- Parts Used:
- 134503600, 5303937139, 5303283286, 131825900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench set
dryer drum quit turning
followed the instructions video on the site had no problems just took about 2 hrs to complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from SAN FRANCISCO, CA
- Parts Used:
- 5308027429
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Noisy squeaky dryer
Main problem was the bearing, replaced the belt and felt seal as well
The video instruction was very helpful
Was easy with basic mechanical aptitude
Dryer running great now
All parts from Partselect.com
Have ordered from them before and would order from them again
The video instruction was very helpful
Was easy with basic mechanical aptitude
Dryer running great now
All parts from Partselect.com
Have ordered from them before and would order from them again
Was this instruction helpful to you?
Thank you for voting!