UAN7214-80C Frigidaire Dryer - Instructions

The repair went very well.The biggest problem was the spring on the tension roller when putting back together.But it just takes a little bit of patients and it was fine.Works great now.

I used the video, and it helped me a lot! I got the drum out, installed the new bearing, greased the new shaft and the receptacle, then I reassembled. When I tested it, mine was still very noisy, so I removed the drum once more and cleaned/added some grease on the tensioner bearing. This was the cause of the noise in my case, but the bearing & housing were nearly shot, so something would have given out very soon. I would suggest to grease the tensioner the first time to save time and effort. (And save some of the grease for the tensioner pulley). SAFETY TIP: there was also a ton of lint that got trapped inside the unit!!! Clean your dryer once per year to prevent it becoming a fire trap!

This video by Steve Ash was spot on . In our case the white rear support bearing had melted and reformed around the shaft, preventing us from being able to pop the drum in the way described in the video. We used pliers to unscrew the screws on the rear clip from the back of the dryer. The rest of it worked exactly as described in the video. Our model was White-Westinghouse DE600ADD1, which is not a model listed on the PartsSelect website. However the part worked very well. The dryer runs really quite now.

the repair when ok the only problem I had was installing the small white plastic piece in the back without losing the ball bearing .and I also vac up everything inside as well lot of lint

i watched the video that is furnished at parts select, it was very useful in doing this repair. i would strongly recommend watching this as i did install the ground bearing wrong to start with,and restringing the drum belt is something you have to feel as your installing it back in place so the video is useful for that as well. my repair was on a front load dryer made by Frigidaire,

I set up my laptop with the partselect video going. Laid out my tools and the individual parts that were in the kit. I watched the video a segment at a time, performing the tasks in the same manner that the instructor did. All together, the process took less than two hours, I had no questions or difficulties, and the repair process went flawlessly and successfully. I had never done anything more complicated on a dryer than replacing the hose before this. The sense of pride in doing a repair of this level myself, and avoiding paying someone ridiculous fees to do it, is beyond description.

Basically followed the You tube videos on standard, stand alone dryers as mine is a stack-able unit. Allow a lot of room to work. Unplug electricity and or the gas, vent hose and water hoses. Start removing screws as per the video, remove Belt then lift up then out the dryer drum. (The drum drops in from above on the back of the unit)the rest is remove and replace as you go. *TIP... I use my phone to photograph tricky areas so I can review as needed. It was more scary then difficult. You can do it!

I followed instructions I found on u-tube to remove the drum and belt and access the bad bearing and change it. The instructions were quite good other than needing to remove a small panel on the back of the dryer to pull the belt around the tensioner.

I highly recommend watching the repair video. I could stop the instructions and do the procedure then resume instructions for the next step. I would recommend you have a second person to help lift the drum up & out of the dryer frame. And ladies please instruct your husbands to watch the video all the way through. Mine lifted the top off the dryer and stuck his hand in and cut his finger immediately on a sharp piece of metal. You know because they don't need to read the instructions.

Followed the video, it was good, the instructor's tips were useful and time saving.

It was super easy! I followed the PartSelect video and everything went fine. Getting the drum out of the machine was a bit tricky but once it was out, the rear bearing kit went in without any problems.

I followed the directions sent by you step for step and the rpair was done in no time at all. Had a little trouble with the roller ball installation but figured out how to install it after a couple of tries. Repair was done with minimal use of standard houshold tools.

It was easy, I handed the part to my husband and he did it!!!!!!!!!!!!!!!

followed the Video instruction which were provided. Dryer works like brand new.

followed vidio instruction which made it easy