FSG748GFS1 Frigidaire Dryer - Instructions

Followed your website repair guides and the great belt replacement video.

Other parts used were; front lower basket seal, dryer seal, and dryer drum belt.

Had no problems except for keeping the drum belt idler pulley tension spring in place. Used the rear access panel to solve this issue.

John H.
Palm Desert, CA

It took about 3 seconds to slide on the new knob. Most important info here -- the new knob has a metal housing inside the plastic that should never strip like the old plastic-only knob. In other words, the new knob is superior to the original equipment. Also, delivery was very prompt. I'm very pleased - thanks!

As others have described in more detail... I lifted the top, removed the 2 screws holding the front panel (one on each side, inside the control panel on either side - not the easiest to get at, but not too bad), popped the clips holding the front panel in place and removed it. With the front panel off, the location of the coils is obvious (lower left side). The only challenging aspect of this repair is that the 2 screws holding the coils in place are really torqued in so it was crucial to use the exactly correct size screwdriver and not let the screwdriver slip while unscrewing those screws. Actually swapping out the coils took seconds, of course they have to go in exactly the same way as the old ones. I did take a few minutes extra to vacuum out years of lint from the inside of the dryer. Overall, much easier and cheaper than I was expecting and now I know where everything is inside the cabinet.

1. unpluged the dryer and turned off the gas.
2. pulled dryer out so i'd have ample room to work on it.
3. used large flat blade screwdriver in the front between the top lid and dryer face to gently pop-up the lid.
4. removed 4 screws from inside, that hold the face to the main box leaving the wires all intact.
Found the coils on the lower left, held in place by two screws and plate.
5. took a good look at thier orientation before unpluging old and installing new, I recommend one at a time.
6. Vacuumm any exceess lint and check foam seal between lint trap and exhuast duc, the glue came undone on mine causing extra lint dust that is potentially flamable.
6. screw dryer front back on to main box, make sure to check wiring harness and that all electrical blade connectors are still pluged in to their componants.
7. At this point plug in, turn on gas and do a test run.
8.if everything checks out good then lower top make sure flexable exhuast hose is still connected on hte back of the dryer.
9. Tell your wife or girlfriend or husband or boy friend they can now finish your laundry :)

Thanks to Justin in Customer Service I was able to get the correct replacement knob. It arrived and I installed it in seconds flat. It works great and you'd never know it wasn't original.

Thanks.

Once I found this site, with everybody's description of the problem & fix, it was pretty easy.
Pry the front of the top up using a flat screwdriver at each side. Then disconnected the dryer-controls wire bundle (dryer unplugged of course) at the connector, and unscrewed 1 screw on each side of the front panel close to the top (under the controls, back-side of the panel), in order to pry the front panel off - top 1st.
With everything opened up, just unscrew the two screws on top of the burner coil. the pull off the plate, slip off the 2 coils, disconnect the wires, and install the new coils in reverse. Put it all back together and you're good!
(I replaced the drum glides too, while I was in there - just in time!)

followed the instructions video on the site had no problems just took about 2 hrs to complete

just put it on in 5 seconds!

Just replaced the new lint filter with the old lint filter. The part fit perfectly. I did not have a problem.

Simple. Just order a new timer knob and fit perfect and snapped right on. Problem solved! = )

First I used a pliers to remove the piece of the broken knob that was still attached to the shaft. Then I pushed the new knop onto the shaft until it snapped into place.

First I was shocked to receive my part the very next day after ordering. The new timer knob went on as easy as you please. I just matched the flat side of the spindle to the flat shaft of the timer knob.

Simply popped it back into place, careful not to break the new handle.

Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!

Just snap into place