DEFW0 Frigidaire Dryer - Instructions

First I have to say that the video on the Parts Select website was invaluable, it truly made the replacement a no brainer. The kit came with everything I need and was a great price.

Unplug the dryer, mine is a stackable so we had to remove the dry from the top of the washer. I then followed the instructions from the video. The only real difference was that my dryer is that is has dual direction tumbling, so there were 2 idler arms instead of one to move in order to un hook the belt. was pretty easy.

I only needed my husband's help a couple of times because 1. To get the dryer off of the washer. And 2. I didn’t have the reach to install the new bearing on the back of the drum.

Removed top panel - disconnected harness from front panel- removed front panel- removed access door to belt tensioner on back panel - took belt off tensioner- removed drum removed upper felt with worn glide pads from front panel - removed most of old glue from panel (small file) and glued on new felt strip with glide pads - let sit to cure removed three phillips screws holding rear brg to the drum and removed brg - removed two phillips screws from rear panel holding plastic bracket, supporting bracket and back clip to the rear panel and replaced with new (use a drop of grease to hold the little ball brg in place during installation, make sure you don't loose it) install new brg to the drum (since they are self cutting screw difficult to install throught he drum, I "pre-cut" one of the threads then installed the rear brg to the drum, screw driver was of ratched type with a long extension - filled the plastic bracket with the grease - installed drum and front panel - tensioned the belt - installed top panel and access rear panel - done - I used the opprtunity to vaccum the interior of the dryer, lot of lint ----------------------------------------------------------------- there is a plastic guide on top of the heating elements which is burnt and should have been replaced but I could not find it in a catalogue. Anybody any idea? Also instructions for glide say to check the paint on the drum, what if it is damaged or gone?

1.) Unplug Dryer
2.) pop dryer lid by depressing 2 front clips with flat head screw dryer
3.) on back of dryer remove access cover and release belt tension
4.) remove front panel screws and then pop off front panel
5.) remove old gasket. Used XACTO knife, razor blades and acetone. Go slow and be careful.
6.) apply new high temp glue, let set up for a minute
7.) position the new felt gasket and clamp into place. I used C-Clamps and squeeze clamps.
8.) I let sit overnight.
9.) re-assemble and good to go.

NOTE: In retrospect I should have replaced both seals at the same time. The bottom seal is pretty worn but is still working out for now.

I followed others instructions on this site to disassemble but felt confident since 2-3 years prior I had replaced the felt top/bottom guides around the drum and the drum belt. The video on this page is also helpful

1) Pop the top with a putty knife
2) Unscrew two screws that hold the front onto the dryer frame
3) Lift front from two clips at bottom of dryer
4) Release tension from belt (unscrew/remove rear access plate)
4) Lift drum up and forward out of dryer
5) Unscrew drum bearing 3x screws from inside of drum
5) Remove the drum bearing holder
6) Pre-thread the rear drum bearing!!! Very important. Thread by screwing a supplied screw slowly through the pre-drilled holes.
7) Attach drum bearing
8) Attach new rear holder/cup & ball bearing (ball bearing goes on outside of plastic cup)
9) Use lots of supplied grease, espeiclly helpful that it acts as a temporary glue holding the ball bearing in place
10) Reverse steps to assemble

I'm glad I bought the entire rear bearing kit as I found the bearing holder had completely worn through and partially melted the metal cup. The ball bearing was missing - gone!

Also found that the power cord had partially melted, so I replaced that from the hardware store. Scary.

We followed the video exactly. The video itself was simple and straight forward. Our model was a bit different than the video's example. The video's example had their spring action for the belt configured differently. When we finally figured out the difference, we were able to finish the job within minutes. The dryer now runs like new. We aren't mechanically inclined. That's why it took us so long. I still would recommend this company to anyone because it saved us time and money. The video really helps!

I had trouble with the little piece on the back side of the dryer not lining up with the bearing housing. I also didn't see how the drum was gonna stay in place but finally realized the front cover lines it up. All in all it was awesome to get the part I needed so quickly and cheap, thanks a lot.

Taking apart cleaning putting back together I don't have any h-t lube so ill be doing it again. Thanks for the part ill be calling again!

Removed front of dryer scraped old seal off ,used brake cleaner on a rag to get old glue off and roughed up seal area with sand paper ,spread glue on attached seal held in place with clothes pin overnight.

1)Unplugged unit from out let 2) Lifted top cover from base by prying up from the from the corners back is hinged 3) removed wires for door switch , removed a screw on the left and right from front. 4) pull front cover out from the top untill it clears drum then lift straight up off bottom clips. 5) scrape off old felt strip and guides 6) Sand untill all felt residue gone apply new glue to front cover wait a few minutes for glue to get tacky 7) clean out all the lint build up Checking from time to time that guide assemble is in place on front cover. 8) reinstall front cover when glue is dry.

Took out the drum by removing rear bearing and replaced with new one. Replaced top glides at same time.

Removed small panel from back of Dryer,and removed Idler Pulley Assembly. From the front,lifted the top of Dryer to get access to the drum,disconnected the two wires for the Stop switch, removed the four screws, two on each side,and lowered down the front panel. Now,removed old belt and installed new, installed new Idler Pulley Assembly,aligned belt with Pulley.Reassembled the front and the top of the Dryer and I was done.The pulley was squeaking,but a shot of DW40 took care the problem.
Thanks

Domenico Intrieri

Excellent!!! The parts fit perfectly, but most of all was the video that went through the repair step-by-step.

A local repairman quoted $198 for parts and another $150 for labor. Got the parts here for less that $26!!!!

The only issue (very minor) was the video called for a phillips head screwdriver to remove the front panel, and our dryer needed a squarehead driver. (If I was younger, I would have been able to see the problem).

But, I highly recommend Partselect!!!!

Pulled the dryer front off to expose the problem. Thought it had a bearing of some type. Went to the PartSelect web site and watched the repair video. The Tech explained everything needed to make the repair. Ordered the parts kit and it arrived in three days by FedEx. Followed the directions. Simple. The video was excellent and made the repair a snap. Thanks.

The part arrived just in the nick of time as my wife and daughter had strung up rope all over the family room to dry clothes. My son helped me lower the dryer to floor level ( this is a stackable washer/dryer set) Removed the top and front of cabinet. Removed the belt and popped out the drum. Took this opportunity to clean the amazing amount of lint from the blower housing and discharge hose ( it is my opinion that the accumulation of lint and the subsequent rise in operating temperature is the main cause of this bearing failure) Removed and replaced the rear bearing and greased it. Reassembled the drum,installed the belt and reassembled the cabinet. the only tools used were a screwdriver and a nut driver....and of course a vacuum cleaner. The rebuild kit is very complete and is the only way to go. Thanks for your fast delivery time, one more clothes line in the family room and I wouldn't be able to watch T.V.

Followed online video. All went smooth. Runs great!!!!!!!!!!!!!