GLER331AQ2 Frigidaire Dryer - Instructions

Followed instructions for removal and installation.

Remove rear control panel cover and remove drum belt from pulleys. remove top cover by pushing in on the 2 hold down fasteners on the front with flat head srewdriver. remove front panel by removing the 2 screws and then pop it out by lifting up. disconnect the wires at the quick connect plugs and set the front aside. lift the drum up to pop it out of the bearing housing and move forward slightly to give youself good access to the wires for the heating element and disconnect the 2 wires. remove drum the reset of the way out and do your work. Replacing the heating pan and drum bearing is pretty obvious what to do. (just a few screws). remove thermal cutoff switch from old pan and install on new pan. reinstall in reverse. no need to label wires because it doesn't matter where the wires go an a switch (justs makes and breaks a circuit) and the heater doesn't matter as long as both wires are hooked up to complete the circuit. You can't mess up the quick connectors on the door. Only my heater failed but I also replaced the drum bearing as long as I had it all apart (only another ~$20). Take the time to clean out the dust from inside the dryer, it will help the blower motor run cleaner and cooler and last longer. I bought a belt also to have on hand for replacement. I didn't replace it since my old one was good and it is real quick to replace at a later time.

I replaced the rear bearing assy. Thanks to all that sent in there stories. very helpful. But my problem was the breaker in breaker box. needless to say "check your outlet for proper voltage.First,before anything else." i had a bad breaker, had it replaced,with proper 30amp fuses.Dryer works fantastic..Thanks to all again for your input. Great Website...

1.Removed access panel on back of machine in order to place a block under the drum(see step 3).2. Removed the top (clips), 3.removed the front panel(clips), block placed under drum earlier prevents drum from tilting and makes removing front panel with door very easy.4. Slipped new belt on. 5.Replaced front panel and removed block under drum. 6. Aligned belt and checked movement of drum, 7. attched belt to pulley on motor and positioned belt tensioner.8. Installed top and access panels.
This repair is very straight forward, block under drum makes things easy, since the drum stays level when the front panel is removed and replaced.

As all others have said, without being redundant, I'd view post #1 or #2 for a good detailed set of instructions.

The primary issue I had was with the stainless steel ball bearing that was shipped with the kit. I couldn't figure out what it was used for, because when I removed the bearing carrier the ball fell out before I could see where the original one was located. The stainless ball bearing is a grounding ball, not a bearing. It goes on the exterior of the plastic bearing carrier/receiver.

Once I figured that part out, it was a piece of cake.

Took a little longer than other people's repairs, but I also put a new belt on and re-worked the exhaust duct for solid ducting versus flexible duct. fine-tuning the rigid duct work was a piece of cake with the tumbler out, since i could crawl right inside the chassis and make sure everything would line up (level legs, adjust elbows, etc)

i read reviews and finally found a person that replace the motor, rear bearing, front top glides, and tension arm/pulley.. i had cleaned the fan motor with a tooth brush best i could the 1 time i had it apart. after the 4th time apart and reading a different review that said replace the fan motor housing/fan. i did and noise gone.

Took a putty knife and released top clips. Tipped top back , and took out 4 screws holding front cover in place. Lifted out drum, replaced bearing plate. Removed 2 screws and replaced back panel bearing. Placed drum back in place, installed front panel, snapped top back in place and job was done. Very easy. Took about one hour.

UNPLUGGED the dryer!!! Search this site they have instructions for many of the tasks they sell parts for... disconnect the vent hose, removed the access panel for the motor & belt (rear) (1/4 nut driver), slipped the belt off the idler pulley and motor pulley, carefully lifted the front edge of the top panel & rotated it back on the hinges, labeled and removed the door interlock wires (2), removed 4 screws securing the top of the front panel (5/16 nut driver) (magnetic is best), removed a yellow guide also attached to the top of the front support (5/16 nut driver), rotated the top of the front panel clear of the drum opening (while supported) and lifted the front panel off the bottom guides, carefully lifted the back of the drum straight up about an inch while supporting the front of the drum, remove the drum from the opening created by removing the front panel (the belt should come out with the drum, removed the rear parts of the new bearing (atteched to teh back of the dryer) 5/16 nut driver... you will need a helper to catch the ball bearing holder on the exterior back of the dryer in the middle, unscrew the drum half of the bearing assembly from inside the drum (3 phillips head screws). I have done this several years ago and you will be amazed at how much dust and lint there is... CLEAN AND VACUUM EVERYWHERE AND THEN ALL THE PLACES YOU MISSED DONT FORGET THE VENT HOSE. Clean all of the old grease from the back of the drum and dryer. Installation is the reverse of removal. Don't forget the new grease and DON"T loose the cute little ball bearing that comes in the new kit. There are lots of sharp metal edges inside so use caution and hopefully you got a new belt since belt replacement requires all of the same steps except for the actual bearing removal.

I can attest to this system only on my model since this is the second bearing I have done.

Sure beats the cost of a new dryer!!! Thanks PARTS SELECT This is the 5th appliance I have repaired for freinds and family with parts purchased from your site.

replaced rear drum bearing kit. Watched video made it real easy. The only problem was getting the belt back on the pulleys.

I looked up a YouTube video on my specific model. Found one that said “basic disassembly”. I watched that and had it apart and back together in no time. Very easy to take apart and put new parts back in it. Re-assembled and since the repair no squeaking.

Followed the video

Remove top cover and front and remove drum and install a new bearing kit and new belt.

Watched video sent to me after I purchased belt on line. Super helpful!

First removed the top of the dryer, then the front of the dryer. Took the plate off the back left of the dryer to disengage the belt off the pulley.
Took the three screws out that hold the drum in place, of course the third screw stripped and had to use a screw remover, which didn't work, but the adjustable pliers did so then lifted the drum out of the plastic reservoir in which the bearing laid. Next unscrewed the two bolts holding the plastic reservoir which also loosened the small metal piece on the back of the dryer where a small bearing is located. Put the new parts in, but instead of putting the larger bearing that fits in the plastic reservoir, I decided to put it on the drum first and guide it into the reservoir all at once, this worked well . Prior to that I put the new plastic piece on the inside and taped it there while holding that piece put the small metal piece with the small bearing on the back of the dryer. I'm sure it is alot easier with two people doing this part, but it worked and I didn't lose the small bearing. Next put the front of the dryer back on and then put the belt back on the pulley, then the top.
It definitely helped immensely to read how someone did this, just follow the instructions given and there you go, no more annoying squeak and also a feeling of accomplishment and thanks to the person who wrote the story on how to do this job, appreciate it.

I followed the instillation instructions provided on your website. They were very informative and spot on. My only problem was my strength. I could not get the drum off of the rear bearing myself, but then I am a 61 year old female.