FASG7074NA4 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Balsam Lake, WI
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dryer wouldn't heat
Removed the panel between the dryer and washer. The gas valve was right in front. The wires were in a plug and easy to remove from old part. The solinoid held in place by a clamp with two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J Martin from Guerneville, CA
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer just barely got warm
Everything I needed to know was already on your website. Prying off the top of the dryer (with a big screwdriver under the front of the top) was the hardest thing, since I was afraid I would break something. Only then can the front be removed (taking out just 2 phillips screws). The rest is easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PETER from Fremont, CA
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
No reheat
Pried the lid up and flipped it back then disconnected the front panel wiring harness and then popped the front panel loose at the top and dropped it down. Disconnected the ignition coils, removed the coil retainer bracket and replaced the coils. Reassembled it in reverse order, performed functional test. Success!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Essexville, MI
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer ran, had no heat
Your website was very helpful in narrowing down and diaganosing the problem. A continuity tester verified an open solenoid. Ordered Sunday evening, parts arrived Tuesday. Ignition coils drop in place with a holddown bracket and one screw. Wiring harness is reattached. Front of dryer is put in place followed by the top. Plugged in the dryer (it is just commom sense to have the power off). Started dryer, of course it ran WITH heat. The end of the story is HAPPY WIFE, HAPPY LIFE. Happy to do business with you. Tom , MI
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond Frattone from Richboro, PA
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door would not close because of broken female latch.
Very simple. I removed the broken latch with pliers and snapped in the new one in less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lukas from Pasadena, CA
- Parts Used:
- 5303207102, 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
latch broken
pulled out old catch with old pliers and popped new one, simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D from Oak Park, IL
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer would heat up but shut off too early
pushed screwdriver into the two clips between the top and front to release the connection. took off front. at the bottom front left side, took out screws to access parts that needed to be replaced. put everything back together. dryer works like new. easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Plymouth, IN
- Parts Used:
- 5303281135
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Heat would come on but not stay on.
Flame Sensor didn't fix it but, it was easy to replace. Unplug electric. Lift up the top and remove wires from switch and light switch. Remove screws that hold on the front and remove front panel by lifting up and out. Sensor is on the left side of the burner, held on with just one screw. EASY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Otsego, MN
- Parts Used:
- 134587700
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer was not drying completly.
I replaced the Control Thermistor (part # PS1149368) by removing the two screws on the bottom of the lower panel below the door. You will see the Control Thermistor just below and to the left of the discharge chute. Remove the two screws holding the Control Thermistor in place. Disconnect the two wire and reconnect to new Control Thermistor. Replace screws in reverse order of above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bret from Tampa, FL
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I shut the door too hard, and the old latch fell down into the inside of the dryer.
The new latch easily snapped it into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Mayfield, KY
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no problem
put door catch in hole
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from Scottsdale, AZ
- Parts Used:
- 137553402
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer gasket keeps coming off
Such an easy repair that I should have done months ago. I knew the gasket was failing but kept fixing the old one until it finally broke apart and couldn't be reused. The new gasket installed within minutes and fit perfectly, not to mention I no longer have to deal with it every time I do the laundry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Brooklyn, NY
- Parts Used:
- 5303931775
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
no heat
Remove top cover 2 screws then remove front panel 6 screws remove wire connecter on the door panel. ignition coil is on the bottom left side need a short hand srew driver remove 2 screws remove plate holding coils remove coils and connecter. Reinstall in reverse installation. Dryer still didnt heat up so back to the drawing board :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TERRY from MILLSBORO, DE
- Parts Used:
- 134197700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner Bad
Ordered part received next day fast shipping was great part in and working thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joan from Roanoke, AL
- Parts Used:
- 131775600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Shreking noise when turning on, then loud noise from dryer, after a few minutes it would not be so loud but louder than normal.
Replaced everything on the dryer till I got the right problem, seriously, I now have a new dryer in an old body, still came out alot cheaper than buying a new one. I listened to every sound on youtube but none sounded like my dryer.
Was this instruction helpful to you?
Thank you for voting!