FFQG5000QW3 Frigidaire Dryer - Instructions

Followed instructions and the repair went very smooth from start to finish. From getting tools out of tool tray to putting them back it took 15 minutes.

I tested continuity on parts like burner (ok) then on solenoids (not ok) timer (ok) I visited several websites and found the AppliancePartsPros.com site with FREE repair forum and found valuable advice. Then ordered my parts at Parts Select and were delivered 3 later at my front door.
Now a days you almost can forget to work on all the electronics in a wasmachine and dryer, unless you're a electronic guru.
THks.

After reading other peoples problems i decided it must be the coils after looking at the picture of the part I looked at the dryer to find were the part was. it was right in front behind the inspection cover. so i order the part. it came very fast.these are not the first parts i have purchased from Partselect.the web site is newer now and i am glad because reading other peoples problems help me decide what was wrong with mine.PS Always clean every thing inside the dryer!! 15-20 min job one screw driver! (19 year old unit works fine)thanks to Partselect!!!

My dryer was heating up very briefly blowing hot air initially then cool. I have a stacking washer/dryer set (2002). I initially turned off the gas valve at the wall, ran the dry for several minutes to clear the gas line, then unplugged the power. I was then able to pop the top using a flathead screw driver, securely prop it open, unhook the wiring harness to the front panel, unscrew the two front panel screws, and remove the entire front without having to unstack the units. From there, you remove the two screws holding the bracket over the coils (2 of them), remove the electrical connectors attached to both coils and replaced them with the new ones. I then replaced all brackets, screws, and such (you'll need to lift the drum when putting the front back on and make sure it is lined up), plugged it back into power and turned on the gas to test the unit which worked perfectly. The 62% of the time seems to be an accurate figure as nothing else had to be done to the unit. Pretty easy stuff...good luck.

Pried the lid up and flipped it back then disconnected the front panel wiring harness and then popped the front panel loose at the top and dropped it down. Disconnected the ignition coils, removed the coil retainer bracket and replaced the coils. Reassembled it in reverse order, performed functional test. Success!

Remove 2 screws at the upper rear attached to the top panel. Slide panel rear back and remove. Remove 2 screws attached to the front control panel. Lift panel upward. Remove 4 screws attached to the front panel (2 at the top, under the control panel, two at the very bottom). Lift front panel up and off, and unplug connector to door switch. Remove some more screws on the internal front panel edges, and the front to back brace holding up the control board. Lift panel up and out, and remove the drum, too. Thermal limiter located toward the rear, attached to the heating vent tube. Disconnect and replace. Re-assemble in reverse order.

Remove top cover 2 screws then remove front panel 6 screws remove wire connecter on the door panel. ignition coil is on the bottom left side need a short hand srew driver remove 2 screws remove plate holding coils remove coils and connecter. Reinstall in reverse installation. Dryer still didnt heat up so back to the drawing board :)

I called a wonderful friend who diagnosed the problem; ordered the repair part; and fixed it!!!

Flame Sensor didn't fix it but, it was easy to replace. Unplug electric. Lift up the top and remove wires from switch and light switch. Remove screws that hold on the front and remove front panel by lifting up and out. Sensor is on the left side of the burner, held on with just one screw. EASY!

I replaced the Control Thermistor (part # PS1149368) by removing the two screws on the bottom of the lower panel below the door. You will see the Control Thermistor just below and to the left of the discharge chute. Remove the two screws holding the Control Thermistor in place. Disconnect the two wire and reconnect to new Control Thermistor. Replace screws in reverse order of above.

Took the coils off and put the new one on thats all

put door catch in hole

pushed screwdriver into the two clips between the top and front to release the connection. took off front. at the bottom front left side, took out screws to access parts that needed to be replaced. put everything back together. dryer works like new. easy.

Your website was very helpful in narrowing down and diaganosing the problem. A continuity tester verified an open solenoid. Ordered Sunday evening, parts arrived Tuesday. Ignition coils drop in place with a holddown bracket and one screw. Wiring harness is reattached. Front of dryer is put in place followed by the top. Plugged in the dryer (it is just commom sense to have the power off). Started dryer, of course it ran WITH heat. The end of the story is HAPPY WIFE, HAPPY LIFE. Happy to do business with you. Tom , MI

Very simple. I removed the broken latch with pliers and snapped in the new one in less than 5 minutes.