7007B Frigidaire Dryer - Instructions

2 screws (Philips) old one out, new one in, real easy..

All I had to do was take out two screws that held the lint screen frame into the dryer, vacuum the opening to get the lint out that had accumulated, place the new frame in the opening, tighten the two screws that hold it in place, insert the lint screen and it was done.

It took me all of 1 minute to take out the old lint screen and drop the new one back in.!!! I didn't need the frame. I had no idea that I could find a replacement so fast!!! Just wish I had not waited a month to look for one. Thanks for the fast service ! !

It was extrememly easy, just pulled out the old screen and dropped in the new one. I didn't use the frame.

Easy, lint trap in front, unscrewed the old base, threw out the old lint screen which was hanging by a thread, and put the new (and - KEY WORD - cheaper) part in. All by Myswlf!

Thanks.

I did not think anyone would even carry the lint screen and frame for our OLD dryer. The price was reasonable and shipping was fast.

replaced

Changed the old one for the new, But the best part was the fast service getting the part. I couldn't believe that I ordered it and three days later it was delivered. Good Job!!!! I will recommend you to everyone.

Replaced new Lint Screen. Changed Frame with two phillips screws. Total time spent: 3 minutes. Two day delivery!

Simply removed the two screws that hold the frame in place, removed the damaged parts, wiped down the surface area where the new one would mount and installed the new frame and screen in the reverse order from removal. SIMPLE and fit perfectly.

I followed others instructions on this site to disassemble but felt confident since 2-3 years prior I had replaced the felt top/bottom guides around the drum and the drum belt. The video on this page is also helpful

1) Pop the top with a putty knife
2) Unscrew two screws that hold the front onto the dryer frame
3) Lift front from two clips at bottom of dryer
4) Release tension from belt (unscrew/remove rear access plate)
4) Lift drum up and forward out of dryer
5) Unscrew drum bearing 3x screws from inside of drum
5) Remove the drum bearing holder
6) Pre-thread the rear drum bearing!!! Very important. Thread by screwing a supplied screw slowly through the pre-drilled holes.
7) Attach drum bearing
8) Attach new rear holder/cup & ball bearing (ball bearing goes on outside of plastic cup)
9) Use lots of supplied grease, espeiclly helpful that it acts as a temporary glue holding the ball bearing in place
10) Reverse steps to assemble

I'm glad I bought the entire rear bearing kit as I found the bearing holder had completely worn through and partially melted the metal cup. The ball bearing was missing - gone!

Also found that the power cord had partially melted, so I replaced that from the hardware store. Scary.

Removed small panel from back of Dryer,and removed Idler Pulley Assembly. From the front,lifted the top of Dryer to get access to the drum,disconnected the two wires for the Stop switch, removed the four screws, two on each side,and lowered down the front panel. Now,removed old belt and installed new, installed new Idler Pulley Assembly,aligned belt with Pulley.Reassembled the front and the top of the Dryer and I was done.The pulley was squeaking,but a shot of DW40 took care the problem.
Thanks

Domenico Intrieri

I had trouble with the little piece on the back side of the dryer not lining up with the bearing housing. I also didn't see how the drum was gonna stay in place but finally realized the front cover lines it up. All in all it was awesome to get the part I needed so quickly and cheap, thanks a lot.

I have a frigidaire dryer about 5 years old.

I first removed the top cover being careful to watch how the wires to the controls are connected. It is best to snap photos with your digital camera so you can remember how to reconnect the wires.

Pulling up on the drum, I lifted it out of the rear sleeve. Once out, you could easily see why it squealed. The metal bearing had groves on it where is made contact with the holder.

The difficult part of this was getting the 3 screws that hold the bearing to the drum off. The phillips screw head was easily marred if you don't have the proper screw driver bit. I think a better screw head would make the job easier.

After removal, the replacement was a snap. When everything was back together, the dryer sounded like new. The job took me about 2 hrs due to the hard part of removing the screws.

Followed video instructions that were emailed by you.