FDE436RET1 Frigidaire Dryer - Instructions

Basically, i followed instructions on 1 video i seen, but was able to shorten repair by not removing drum, and was still able to access the thermal limiter switch to remove old one and install new one. Worked like a charm. Thanks Dan

After the part arrived, I located a pair of needle nose pliers. Then removed the broken one and inserted the new one. It was very easy.
I also noted that the new part was of a better design than the original. It should not need further attention.

I unpluged the machine. Pried out the old switch with the tip of a screw driver. Pried off the connectors, there was not enough extra wire for me to connect the new switch through the front of the machine. I pushed the new switch in place. Using the screw driver I carefully pried open the top front of the machine { there were 2 plastic spring clips securing the top}. I placed a wash bucket on the drum to hold the top open , connected the 2 connectors to the switch and snapped top back in place.

I noticed for sometime that my dryer had been sqeeking...but I had thought nothing of it. It got alot louder as time went on and then one day the drum stopped spinning. Not to mention I had my son's 5th birthday party in 3 days. So I went online and found parts select. They sent me the whole assembly and I got it the day before the birthday, and it only took me 30 mins to replace it. Thank you, Parts Select for the prompt response and saving me for the embarrasment of having clothes all over the floor.

The repair went very smoothly. I'm a woman in my mid 20's and was prepared to buy a new dryer but I saw the part online for a very reasonable price and the video instructions were extremely helpful. I was able to fix the dryer quickly and cost effectively AND the part arrived in only 2 days! It all worked out very well.

first i removed the top -second I removed the two screws hold the front on - thrid I unpluged the wiring to remove the front - fourth I removed old part and cleaned off old glue -fifth I applied new glue and new part - sixth I reasembled - worked good as new

removing was easy just open lower rear LH panel . Ordering was easy ,shipping seemed like alot? to install the new belt pop top of dryer I used a screw driver to help. remove front panel 2 screws then it also has about six clips may have to have gloves on so you do not skin your hands like I did.... lots of sharp edges. pay attention to the clips, so if they come off they will not be lost. panel will tilt slightly fwd then raise up and set aside. now you can slip the belt over the drum. I kept all the slack at the top till it was in position. the groved rubber side goes against the drum and the motor pully. then extend the spring tensioner into position . I rotated the drum a few times by hand to make sure everything was in position. replace front. check it is lined up well before forceing clips in. check felt material is properly in place, as you rotate it into position. push down top . good to go. I ran it for awhile watching everything work before placing it back in service. you may want to clean it out some while it is apart I used an air compressor and shop vac simultaniously as that seemed to work best. Wanted my son to do it as I think he had it over loaded as to why it broke? It maybe the bearings are going but it felt solid ?? I should find out in a month or so shich was which! I did not see any easy way to get to grease it. The belt was easy though pretty sure my son could have handled it!

the catch on the door was worn and cracked.... so I noticed it could be easily popped out with a screw driver and when the new part came in the mail 2 days later, it was just as easy to pop back in with no tools required. Now the door stays shut really good!!!

First make sure dryer is unplugged.Next beware of sharp edges, this dryer has plenty. Remove 2 screws from kick panel,remove kick panel. Lay the kick panel aside, it makes a good "bowl" to hold screws.Remove 2 screws from top, located on back,remove top.Unplug the 2 sets of wiring connecting the front panel, the zip tie has to be unzipped, and if stripped should be replaced when reassembling. Remove 2 screws inside cabinet that hold front panel, near top. Remove 2 screws that hold front panel, in front and at bottom of front panel. Front panel is held in place by spring loaded clips, remove by pulling outward,a putty knife may be slid in to persuade it to pop off, be careful of scratching paint. There is a small panel on the back of the dryer held by 2 screws, remove to access the pulley that maintains tension on belt and release belt. Pay attention to the belt route through the tensioner to insure eaiser assembly later. Remove nylon drum retainer in front of cabinet at top, held in place by 1 screw. The drum may be lifted out and placed aside to access the heating unit(Don't place it on a hill, HaHa). The entire heating unit may be replaced, I opted to replace just the element, as it is much cheaper.
Use a flat screw driver to slip old female plugs off male element plugs, Use needle nose pliers to flatten tabs that hold male plugs of element in the ceramic housing. Remove old element, being careful not to damage any of the insulators. If the new element is not stretched out to about 46 inches "relaxed", carefully stretch it. Place one insulator slightly off-center on the element and place it into element housing. Plug in element into ceramic plug housing and bend the tabs to retain it. carefully begin putting in insulators, one at a time and reattaching element. Do not bend the element or cause any of the coils to touch each other. When all insulators are in place, plug in element and assemble dryer in reverse order. Mke sure belt is oriented with grooved side facing drum, and reach through the rear access panel to run belt through tensioner, make sure spring is attached with s-hook ends and belt is properly threaded. Reaasmble in reverse order, being careful to make sure drum bearing is seated properly, and drum "ring" of front panel is centered in drum. After dryer is assembled try it out on cool and work your way up to hot, and let it run a few minutes to get rid the new smell. Hope this will help.

The hardest part was getting to the part and removing it and putting it back on. The schematics that you had on your website helped us locate where it needed to go and, hopefully, that will solve our problem.

Girls you can do it on your own!

The easiest way is taking the back off the dryer but if you can't do that just pop the top up and unscrew the front. Just make sure you remember how you take everything out and put it back in the same.

The most difficult part is trying to line up the holes for the heating element, and holding it there while screwing the element in place.

It's a breeze!

All I did was push the new part into the machine! So easy!

I took the repair video in with me and set my lap-top on top of the washer.
My dryer did not match the type on the video exactly (mine has the controls in the front instead of on top and in the back) - however - the parts replacement for the rear drum bearing itself was the same.
After getting the front apart and releasing the drum the rest was pretty easy. Didn't really need instructions for the heating element - that was an obvious change out.
The tips on the video changing the rear drum assembly were very helpful.
Just watch the vid and do it! It took me exactly two hours since I was also changing out the heating element and I did it on a Friday night while having a couple tasty beers.
One tip I would give is the old grease in the bearing is very messy and I got it all over my shirt and pants - and when changing that stuff out don't lean on the front of the frame - I did and bent it out of whack a bit.
The dryer runs like new now that it's done!

1 Unplug the dryer and Raise top up by releasing the clips and fold back to expose the drum. 2. Take Phillips head screw driver and remove two screws inside the front dryer panel and then take flathead screwdriver to pop out both sides and set aside. 3. Lay on your stomach and reach inside to the belt pulley and push right so the belt will release then stand to either side of dryer and grab the belt and lift the drum up out of its bracket. 4. Go to the front and pull the drum out and replace the Rear Drum Bearing Kit . 5. Grab the front panel and remove the Top dryer guide and replace to match evenly with the bottom dryer guide by cutting at least 1/8 -1/4" from felt and use High temp adhesive to glue down. 6. Replace everything in order that was taken apart and reconnect electrical plug and start dryer.

The new motor from parts select was not correct. The new motor is a bolt on. The original motor was a press on. Had to return at a cost of 42.00 dollars. Had to buy a new dryer.