WDG336RED0 Frigidaire Dryer - Instructions

So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.

I first looked at your directions then felt I could do the repair. So I ordered the part. The video was extremely helpful and allowed me to follow each step in the process. Last time I paid $270 for the exact repair. This time I costs me under $30. Plus I was able to clean out the entire inside of the dryer. The sitr instructions were very helpful and on target for any level of experience. I fixed my own dryer and saved a ton on it! Thank You, Randy In Colorado

Had to open back side vent & use needle nose to secure spring.

Partselect provided me with what to look for with my symptoms and excellent delivery time.

This was a simple repair. Before I ordered the parts I had read several of the "repair stories" on this site, plus my neighbor explained to me the process. So I had a good idea of what I was getting into.

I am not real sure how long it took because I was watching a football game while I was making the repair, but I would guess if I did it straight through it would be about 1 hr.

Replacing the Drum Glide and Lower Basket Seal
1) Pulled dryer out from the wall
2) Unplugged Dryer
3) Pop the top off the dryer. Insert a screw driver in the crack right at the corners to pry
the top off.
4) My dryer had a quick connector for all the wiring (which I found half way through the
repair) that allowed me to disconnect all the wires leading to the door. If you can find
that disconnect that so you can easily remove the door & front panel.
5) Removed two screws holding the front panel on.
6) Remove the front panel. Once the 2 screws are removed the only thing holding my
front panel on were a couple of clips.
7) Removed the Drum Glide (top) & Lower Basket Seal (bottom) around the door frame in
the front panel. This is the worst part because you have to scrape a lot of the glue
and it takes a little while to do this.
8) Glue the Drum Glide. I used some spring clamps to hold it in place. Glue did come with
the Drum Glide (but not the Lower Basket Seal)
9) Glue the Lower Basket Seal. Since I only had 4 spring clamps I waited until the Drum
Glide was secure. So if you have several of these clamps that would be best.
** if not replacing the belt skip that section.

Replacing Dryer Drum Belt
I took a lot of the people's advise and replaced the belt while I had the dryer apart. But if you are only replacing the belt perform steps 1 - 6 above first.
1) Remove the access panel on the back of the dryer. Mine had for screws.
2) Remove the belt. There is a spring loaded pulley that you just move to one side so the
belt will loosen up enough to remove.
3) Place the new belt on. I started in the front and moved the belt over the drum to the
back. Then moved to the back of the dryer and through the access panel placed the
belt over the pulleys.

Thats pretty much it. I barely got dirty. Oh, while I was in there I cleaned as much lint as I could. That was the dirty part. Now all you have to do is put it back together.
1) Reconnect the front panel, and wire harness.
2) Plug it back in.

If you are wondering why I didn't replace the bearing, I didn't have any grease and the part fit but didn't look exactly like the current one. And the current one looked ok. Since this was my first attempt at fixing a dryer; I decided not to press my luck.

I followed the instillation instructions provided on your website. They were very informative and spot on. My only problem was my strength. I could not get the drum off of the rear bearing myself, but then I am a 61 year old female.

The first thing I did was logged onto the internet to search the web for my dryer information. Next, after I found the correct model, the site referred me to the parts section and that is where I determined the problem was the M series ignition coil. I then unplugged the dryer and turned off the gas. I took a screwdriver and popped the top off and cut the wire straps that held the door strips and the light to the front panel. I then unplugged the door switch at the connector - HOWEVER - DO NOT TRY TO REMOVE THE WIRES FROM THE ACTUAL DOOR SWITCH BECAUSE THEY ARE VERY FRAGILE AND CAN EASILY BREAK. Next, I removed the two screws that hold the front panel on. By using a slight bit of pressure, I removed the front panel and was able to locate where the ignition coil switch was. (It was right in front) I then removed the two screws that held the clamp down, as well as the bad coils. The coils easily slid off the post and the new pieces slid back on just as easy. I then replaced the screws and clamps to hold the new pieces in place and replaced the front panel. **NOTE ~ while the front panel is off, it would be a good time to clean out all the built up dirt and lint that has accumulated over the years. Lastly, I re-connected all switches and wires and replaced the top panel. Once I turned the gas back on, everything ran beautifully.

Opened top of dryer with screw driver,removed two screws securing the front door. moved door away from dryer. Removed old felt from door,scraped area to remove old glue and felt. Lightly sanded area to clean. Applied new provided glue and let set for 1 minute. put new felt in place and applied three small clamps to hold in place. Waited 1 hour and reassembled dryer.

took apart and replaced parts easy to do but no one in my town can get me parts. thay want 100.00 gust to come out and look at it so found parts online and thats that

I unpluged the dryer, raised the top cover up, removed 2 two screws & pulled front cover out. Removed the old seal, cleaned the area & installed the new seal. Reinstalled as new. Very, very easy.

popped in one in

I unscrewed the 2 screws on the side of the door and the 2 screws on the bottom of the door, removed the broken handle and r replaced it with the new one.

Took out of package. Used screw driver to pop off old broken handle.
Installed new part in a minute or two. Nothing to it. Was very pleased to get the part and so easy to install.

Ordered part from partselect.com. Part was back ordered; however they were very proactive in communicating status updates! When it arrived it was simply a matter of removing door using a philips screwdriver, installing the new hinge and presto - job complete! Kudos to partselect.com ??

Snapped the new door handle replacement from this site in place. Fits perfectly.