FDE336NBS2 Frigidaire Dryer - Instructions

Just like in the video, but with a stackable washer/dryer unit, works like new now....

Opened the top of the dryer (no tools needed).
used socket set and removed the two screws (one on each side). unpluged wires from front panel, labled each (good practice).
Pulled open the front panel.
cleaned old felt off all around the front panel. Wiped down everything. while I had it opened, I vaccumed out the dryer underneath.
used glue provided in felt kit and glued new felt where old was.
let dry, put front panel back on ensuring that the felt was between drum and front panel.
put screws back in front panel. closed top.
Let me say that this is the third time I've done this to this dryer as it is about 18 years old.
Until the heating coils go out, this is the cheapest fix there is. :-)

1.Removed access panel on back of machine in order to place a block under the drum(see step 3).2. Removed the top (clips), 3.removed the front panel(clips), block placed under drum earlier prevents drum from tilting and makes removing front panel with door very easy.4. Slipped new belt on. 5.Replaced front panel and removed block under drum. 6. Aligned belt and checked movement of drum, 7. attched belt to pulley on motor and positioned belt tensioner.8. Installed top and access panels.
This repair is very straight forward, block under drum makes things easy, since the drum stays level when the front panel is removed and replaced.

I took the dryer apart to vacuum and check because of the screaching noise. Took drum out and found the bearing in pieces and shaft had rubbed against the brace. I thought as old as my dryer was I would never get a piece to fix it. I got online and found PartSelect.com. I found the part but could not tell if all was included. there was a Phone Number so I called it. I was helped instantly. They acted like it was no big deal to have a dryer that old. I got my part within a week and had my dryer back together. It works like new. Thank you

Took a putty knife and released top clips. Tipped top back , and took out 4 screws holding front cover in place. Lifted out drum, replaced bearing plate. Removed 2 screws and replaced back panel bearing. Placed drum back in place, installed front panel, snapped top back in place and job was done. Very easy. Took about one hour.

UNPLUGGED the dryer!!! Search this site they have instructions for many of the tasks they sell parts for... disconnect the vent hose, removed the access panel for the motor & belt (rear) (1/4 nut driver), slipped the belt off the idler pulley and motor pulley, carefully lifted the front edge of the top panel & rotated it back on the hinges, labeled and removed the door interlock wires (2), removed 4 screws securing the top of the front panel (5/16 nut driver) (magnetic is best), removed a yellow guide also attached to the top of the front support (5/16 nut driver), rotated the top of the front panel clear of the drum opening (while supported) and lifted the front panel off the bottom guides, carefully lifted the back of the drum straight up about an inch while supporting the front of the drum, remove the drum from the opening created by removing the front panel (the belt should come out with the drum, removed the rear parts of the new bearing (atteched to teh back of the dryer) 5/16 nut driver... you will need a helper to catch the ball bearing holder on the exterior back of the dryer in the middle, unscrew the drum half of the bearing assembly from inside the drum (3 phillips head screws). I have done this several years ago and you will be amazed at how much dust and lint there is... CLEAN AND VACUUM EVERYWHERE AND THEN ALL THE PLACES YOU MISSED DONT FORGET THE VENT HOSE. Clean all of the old grease from the back of the drum and dryer. Installation is the reverse of removal. Don't forget the new grease and DON"T loose the cute little ball bearing that comes in the new kit. There are lots of sharp metal edges inside so use caution and hopefully you got a new belt since belt replacement requires all of the same steps except for the actual bearing removal.

I can attest to this system only on my model since this is the second bearing I have done.

Sure beats the cost of a new dryer!!! Thanks PARTS SELECT This is the 5th appliance I have repaired for freinds and family with parts purchased from your site.

As all others have said, without being redundant, I'd view post #1 or #2 for a good detailed set of instructions.

The primary issue I had was with the stainless steel ball bearing that was shipped with the kit. I couldn't figure out what it was used for, because when I removed the bearing carrier the ball fell out before I could see where the original one was located. The stainless ball bearing is a grounding ball, not a bearing. It goes on the exterior of the plastic bearing carrier/receiver.

Once I figured that part out, it was a piece of cake.

Took a little longer than other people's repairs, but I also put a new belt on and re-worked the exhaust duct for solid ducting versus flexible duct. fine-tuning the rigid duct work was a piece of cake with the tumbler out, since i could crawl right inside the chassis and make sure everything would line up (level legs, adjust elbows, etc)

there are several srcews to remove. there are some u dont have to take out but it looks like u do.ease of the front panel and remove the old drum glide,very hard to get of all the felt.check the the bottom guide before u order parts if possible(i could've replaced mine,but didnt have time to check it first).when glue back in place follow directions exact and clamp.allow glue to dry as long as u can. mine set overnight it was nice and dry(if u dont you'll be doing it all over again)replace everything as you took them off.all works great perfect fit!!

First, I popped the two clips that hold on the top. Then, I removed two screws and unplugged a few wire connectors to remove the front panel. I scraped off the felt, which was rubbing the drum since the white plastic glides had worn completely through. I applied the high-temp adhesive liberally, laid on the new felt, and applied some spring clamps to hold it in place. I removed the small back panel to replace the belt, which was really easy with the dryer apart. The 7-year-old original belt was a little cracked.

I removed the cracked knob and attempted to replace with the new knob. Unfortunately my new knob did not fit. The internal diameter of the replacement knob was 2mm too small. I did not want to go through the hassle of returning and requesting another knob. So I just made it work. Thanks

I watched the video you had. Did what the man said, checked out the parts, and orded the new ones. Then installed , as per video. It was Fun.

First of all, I LOVE Partselect.com.. The parts are reasonable, and arrive in a timely fashion.. The repair stories are far and away, one of the BEST features of this website - so hats off to the DIY'ers who have helped me overcome my challenges and helped me stay in the ..ahem.. "favorable" graces of my wife.. I need all the help I can get there.. Anyway, read the other repair stories first - LOTS of great insight.. I only have a couple pointers to add - below...

This is easily my 4th appliance repair project with Partselect.com, and I can say without a doubt that the experience has been positive every single time.. Until now.. I got the dryer torn down and realized that I SHOULD have ordered the SEAL-BASKET LOWER felt with my original order. When I inspected it for my list of parts to order, the upper glide was thrashed - no brainer.. I thought the lower felt was fine.. d'oh! I discovered this morning that I was wrong.. So, I JUST ordered the lower basket seal for *next* weekend.. (If you are gonna replace the original upper glide, replace the lower basket seal as well..) It'll be a slam dunk, though..

Now, for a couple useful tips:

If you are a car guy, get out your trusty can of brake parts cleaner to help clean off the old adhesive residue after you rip off the old upper glide felt. I also used a 1" plastic scraper to help facilitate removal, but the brake parts cleaner was a Godsend. I think I read someone else's suggestion to use "goof off" or whatever - but I couldn't find mine, so..... ...out came the brake cleaner... :) two thumbs up. Just use it sparingly - all those solvents are bad for children in California for some odd reason..

Spring loaded clamps to hold the felt down as the glue dries are also "nice to have". I used one on each end of the felt, and one for each of the teflon / plastic glides..

Finally - milk this job for all it's worth - it'll only take you 45-60 minutes or so... good luck...!!!

popped in one in

took apart and replaced parts easy to do but no one in my town can get me parts. thay want 100.00 gust to come out and look at it so found parts online and thats that

Slid on new knob. The turn around time on receiving the part was amazing. We were back in business within 2 days.