FDG546RES0 Frigidaire Dryer - Instructions

I am a "do-it-yourselfer" despite my husbands opposition. I followed instructions from one of the posts on the site and took apart the dryer. I found the location of the rear bearing and took it out and replaced it with the new one. Easy as that. Made sure the parts looked the same. Made sure I saw how everything went together. I used a magnet to hold the ball bearing in place on the rear mount and taped the metal bracket on the outside of the dryer. Screwed it right in. Reassembled in reverse and works like a charm. To all the women out there who don't think they can do this. It's easy. Give it a try.

Disconnected power cord; lifted top using putty knife to open spring holds on the sides of the top; released front panel by removing screw from each side;removed old glide and glue; glued new piece in place; reconnected all parts and let dry overnight.

A caution to take care of sharp/rough edges when removing old felt and glide. Goof Off worked well enough along with elbow grease to remove the old glue. A stonger solvent may have worked better, but did not want fumes and residue in the area.

Fit of new glide was straightforward and fit well to the lower felt glide..

(Turns out that the squeak was primarily from the rear bearing that needed some cleaning and grease, but am glad to have replaced the worn front glide)

First unplugged the dryer took off the top. Removed the 2 screws holding the front panel on. Scraped and cleaned old drum glide and lower basket seal. glued new seals on replaced lightbulb while I had it apart then reassembled. It was an easy job and the wife is now happy again.. Thanks to Partselect.
Mike

I took the new door catch out of the packaging and just snapped it in place it was easy peasy and took less time than opening the package

After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on the belt tenioner pully. If the squeel goes away, you have found your smoking gun.

So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.

Slid on new knob. The turn around time on receiving the part was amazing. We were back in business within 2 days.

I know that the knobs on the Gibson dryers break as they are plastic and the back cracks so it won't turn. I have had to get several new ones over the years. I went to Google put in Gibson dryer knob and found it, I had the model number so that helped. I had the part within 24 hrs, awesome service from PartSelect.
Emma W

Took out of package. Used screw driver to pop off old broken handle.
Installed new part in a minute or two. Nothing to it. Was very pleased to get the part and so easy to install.

When the part was delivered I opened the box and unwrapped the knob from the protective paper. I walked down the whole length of my hallway to the laundry room and carefully approached the dryer. Stealthily I reached across the top of the dryer and slid the knob onto the metal rod. Voila! I am now a certified Frigidaire Clothesdryer Repairperson!!

I just used a putty knife to remove the broken one. It just popped right off.
The new one just popped into place.

I want to say that the girl / lady that answer the phone was extremely helpful and very professional,.

I unscrewed the 2 screws on the side of the door and the 2 screws on the bottom of the door, removed the broken handle and r replaced it with the new one.

Snapped the new door handle replacement from this site in place. Fits perfectly.

Opened top of dryer with screw driver,removed two screws securing the front door. moved door away from dryer. Removed old felt from door,scraped area to remove old glue and felt. Lightly sanded area to clean. Applied new provided glue and let set for 1 minute. put new felt in place and applied three small clamps to hold in place. Waited 1 hour and reassembled dryer.

took apart and replaced parts easy to do but no one in my town can get me parts. thay want 100.00 gust to come out and look at it so found parts online and thats that