AEQB6400FS0 Frigidaire Dryer - Instructions

All I did was push the new part into the machine! So easy!

I took the repair video in with me and set my lap-top on top of the washer.
My dryer did not match the type on the video exactly (mine has the controls in the front instead of on top and in the back) - however - the parts replacement for the rear drum bearing itself was the same.
After getting the front apart and releasing the drum the rest was pretty easy. Didn't really need instructions for the heating element - that was an obvious change out.
The tips on the video changing the rear drum assembly were very helpful.
Just watch the vid and do it! It took me exactly two hours since I was also changing out the heating element and I did it on a Friday night while having a couple tasty beers.
One tip I would give is the old grease in the bearing is very messy and I got it all over my shirt and pants - and when changing that stuff out don't lean on the front of the frame - I did and bent it out of whack a bit.
The dryer runs like new now that it's done!

followed the repair video and replaced thermal fuse and thermostat(recommend replacing both due to the problem could of resulted in either part being the cause),Repair went relatively easy.I also recommend to clean and vacuum the dryer while you have it all apart due to a lot of lint buildup and don't forget to unplug before servicing!Stay Safe!!!

i first looked up the diagram for this model and checked for the best way to take the front cover off the dryer. after removing the front cover i start looking for the wires that connect the door switch and remove the wires. the front cover also supports the weight of the drum, so carefully pull the cover until the drum comes loose. at this point you can visually see the parts of the parts that make up the workings of the dryer. i first noticed the drum was coming out with the front cover at this time i knew the rear drum assembly was broke. i then took the belt loose from tension pulley and slid it off the drum and removed both from the cabinet. after the drum was removed i also noticed the heating was broken in several places. i removed four screws from the heating element assembly and also removed two wire that were connected to the element. with all pieces removed i checked the thermal switches, there are three switches, one on the heating element, one on the vent side and one on the back panel of the cabinet. i then installed the rear drum assembly and the heating element assembly and connected the wires. i then slid the drum almost all the in place and put the new belt around the drum and dropped the rear drum into the bracket that supports the rear drum then run the belt around the tension pulley and around the motor pulley. i then placed the front panel back in place and connected the wires for the door switch and lifted the drum assembly up just enough to insert the front panel door support into the drum and placed the clips in place, checked all connections twice and connected power back to the unit and turned on and run it through all its settings.

I removed dryer exhaust hose.unsnapped top cover the clips are in front and exposed inside of dryer,remove 2 screws on inside of front cover and set aside. remove lower cover in back and push belt extender until belt is loose remove 3 screws on inside of tumbler. remove tumbler out the front of dryer be careful not to damage belt set aside remove ball plate by pulling up and out it will unsnap. Now remove 2 sets of wires that are connected to heater element plate remove 4 screws holding element plate in place. Since dryer was all exposed I cleaned everything out with a wet vac put back together following instructions in reverse. Good luck

popped the catch in existing hole and replaced the screws

I remove the old lint filter and just put the new one in.

Removed the back panel and the exhaust hose.removed the heater element and changed the thermostat wire was melted cut damaged part of wire soldered and rapped with black electrical tap

Replace rear bearing, found Exhust tube seal broken. Went ahead and replaced Drum belt & Idler arm assembly. Works like New !

Watched a YouTube video. Very easy to replace, I’m 73 year old woman…this was a very easy job, anyone can do it!

I disassembled the dryer using instructions from the following website for White Westinghouse (pictures really helped)
After removing the drum, I first noticed that the grouding ball was sitting on the bottom of the dryer (along with much lint). I then saw that the bracket for bearing support cup and the bearing support cup were both worn well past use. The bracket had been worn down about 1/4" to the SE with matching wear on the bearing support cup. There was a hole in the bottom of the bearing support cup (hence the grouding ball on the floor of dryer).
I installed the new idler pulley assembly and completely vacuumed out the dryer (I didn't know lint could get so stiff!). I installed the new parts from the kit once received (and the new belt bought previously) and the dryer works great. I'm so used to the obnoxious squealing that it seems odd to be so quiet.

The internet is a magnificent thing!

First, I had to decide if it was reasonable to attempt the repair. Was it worth spending $160 to see if that would fix it, or would I just find out I'd have to start fresh and buy a new dryer, in which case the cost of the (failed) repair would add to the total cost. I was sure enough a new Control was the answer, the decision was to go ahead.

I was concerned about getting the right part, but between your search feature that assured me my selection "will fit your unit", and the option to return the part if it wasn't right, I felt confident enough to order it. Also I was concerned about having good instructions to follow, but there was a YouTube video that showed all the details clearly. The included written instructions gave the general sequence to follow, but weren't for my specific model.

The actual repair was easy. Because the washer and dryer were stacked, it was harder to get to the back screws than in the YouTube video. I stood on a stepladder, and used an awl (with a mirror) to line up the holes when re-securing the top lid because I couldn't see them directly. I compared the new Control with the old by looking through the anti-static bag. If it looked wrong I wanted to be able to return it, and it had to be unopened to do so. Undoing the connectors, unscrewing the frame pieces holding the board, swapping out the boards, and putting it all back together went fine with the help of the video. I would recommend marking the old board to avoid installing it again by mistake. No, I didn't do that, but the old board was hardly dirty or worn and didn't look much different than the new one. Also, I didn't drop any of the screws, but if you do and they go down behind the unit or into it, one of those magnetic telescoping hardware retrievers might be useful.

That fixed it! 160 bucks instead of whatever a new dryer costs these days is a good tradeoff, and a whole lot less aggravation. It's been working fine ever since.

Previous comments on line were so helpful.

My husband and son took the dryer apart by removing the top in order to get to the drum. Part of silver rim that the Drum Glide is attached to was broken,it had been cut somehow. They had to soder it back in place so they could attach the Drum Glide and so far it's working.

Felt- I just ordered one with the adhesive and removed the damaged section used a wire brush, applied the adhesive ( which was more than enough) waited a few minutes for the adhesive to set, applied the felt, attached binder clips to hold it in place while working on the Drum Glide. Really easy.

First of all, the folks at Part Select have been terrific. I balled up my address and they were great in correcting my error and getting the parts promptly to me. They provide directions with the parts. And You Tube, is a wealth of information too. The process is to remove the drum and replace the nylon busihing that supports the drum at the back of the machine. Getting it out was no sweat. Getting the drum back in was a bit more challenging single handed. If I was going to make any suggestion it would be this is a good project for two sets of hands with the second set needed for about ten minutes. The You Tube video I watched said putting the front cover with the drum attached to the back of the unit would be the challenge and they were right. Otherwise, super easy and the results are it's back to "new" condition. Thanks again to Part Select!

Watched on-line video, then applied those steps.
1. Pop the front of the deck loose using putty knife to depress clips;
2. Disconnect wires from light and door switch;
(Before I disconnected wires from door switch and light, I made wiring sketches to make sure I reconnected in original manner.)
3. Remove lint filter mount screws and mount from bottom of door opening;
4. Cut drum belt with wire-cutters and removed it;
5. Remove drum support clip from top center of front panel;
6. Remove (1) screw from each side of dryer body that hold front to sidewalls, removed front panel;
7. Remove drum by lifting the rear out of the bearing, then moving it forward through the machine front;
[While I had the dryer disassembled, I thoroughly cleaned it of lint, dirt & metal filings. The metal filings were from the worn ball hitch and drum support bearing cup. I spent as much time cleaning it out as I did working on it.]
8. Stand drum on gallon paint bucket while removing ball hitch (Use a #2 drywall phillips apex to obtain sufficient seating & torque to remove and reinstall ball hitch screws at rear of drum.);
9. Have a second person hold the new ball hitch in position while starting screws, if necessary;
10. Use nut driver w/5/16" socket to remove bearing retainer & ground ball clip;
11. Install new bearing into retainer clip, insert attachment screws through the holes in both, stick grounding ball in depression on back of bearing as screws are fed through back panel;
12. Hold ground ball clip in place to start one screw, then the other & tighten with nut driver;
13. Start drum belt on motor shaft and position against tensioner pulley;
14. Feed drum through front of machine and loop belt over rear of drum;
15. Slide belt forward on drum as drum moves to rear to keep it aligned with position of tension pulley;
16. Lift rear of drum to place ball hitch on top of bearing, then press down to seat it into bearing;
17. Turn drum to ensure belt alignment, then re-accomplish steps 6 thru 1.