GDD15A1W5 Frigidaire Dryer - Instructions

Followed online video. All went smooth. Runs great!!!!!!!!!!!!!

I have a frigidaire dryer about 5 years old.

I first removed the top cover being careful to watch how the wires to the controls are connected. It is best to snap photos with your digital camera so you can remember how to reconnect the wires.

Pulling up on the drum, I lifted it out of the rear sleeve. Once out, you could easily see why it squealed. The metal bearing had groves on it where is made contact with the holder.

The difficult part of this was getting the 3 screws that hold the bearing to the drum off. The phillips screw head was easily marred if you don't have the proper screw driver bit. I think a better screw head would make the job easier.

After removal, the replacement was a snap. When everything was back together, the dryer sounded like new. The job took me about 2 hrs due to the hard part of removing the screws.

Excellent!!! The parts fit perfectly, but most of all was the video that went through the repair step-by-step.

A local repairman quoted $198 for parts and another $150 for labor. Got the parts here for less that $26!!!!

The only issue (very minor) was the video called for a phillips head screwdriver to remove the front panel, and our dryer needed a squarehead driver. (If I was younger, I would have been able to see the problem).

But, I highly recommend Partselect!!!!

We followed the video exactly. The video itself was simple and straight forward. Our model was a bit different than the video's example. The video's example had their spring action for the belt configured differently. When we finally figured out the difference, we were able to finish the job within minutes. The dryer now runs like new. We aren't mechanically inclined. That's why it took us so long. I still would recommend this company to anyone because it saved us time and money. The video really helps!

Taking apart cleaning putting back together I don't have any h-t lube so ill be doing it again. Thanks for the part ill be calling again!

Followed video instructions that were emailed by you.

parts arrive just like they said they would .had parts installed with in 15 minutes was drying clothes thank you your advice was perfect.

The part arrived just in the nick of time as my wife and daughter had strung up rope all over the family room to dry clothes. My son helped me lower the dryer to floor level ( this is a stackable washer/dryer set) Removed the top and front of cabinet. Removed the belt and popped out the drum. Took this opportunity to clean the amazing amount of lint from the blower housing and discharge hose ( it is my opinion that the accumulation of lint and the subsequent rise in operating temperature is the main cause of this bearing failure) Removed and replaced the rear bearing and greased it. Reassembled the drum,installed the belt and reassembled the cabinet. the only tools used were a screwdriver and a nut driver....and of course a vacuum cleaner. The rebuild kit is very complete and is the only way to go. Thanks for your fast delivery time, one more clothes line in the family room and I wouldn't be able to watch T.V.

I removed the panel's that enclosed the drum, removed the drum and cleaned all the lint around the drum, heat panel, drive motor, and switch's.
removed the old support bearing and grounding ball then applied grease into the new support hub and reinstalled the new hub and grounding ball and then reassembled the dryer. Runs like it was new.

After reading other peoples problems i decided it must be the coils after looking at the picture of the part I looked at the dryer to find were the part was. it was right in front behind the inspection cover. so i order the part. it came very fast.these are not the first parts i have purchased from Partselect.the web site is newer now and i am glad because reading other peoples problems help me decide what was wrong with mine.PS Always clean every thing inside the dryer!! 15-20 min job one screw driver! (19 year old unit works fine)thanks to Partselect!!!

after cutting the power, I used a putty knife to release the two holding clips ot remove the top,, 2 foward facing screws on either side of the front and two cap covered screws holding the bottom and unhooked the two electricial connections for the control panel and removed the front panel. Since this was a stack unit and in a closet most work had to be done from the front. By reaching inside to remove the belt from the motor,removing the drum was the easy part, to get to the bearing, but unfortunatly I had to remove the dryer from the closet to replace the back bearing clip and ball. After that replacing the bearing bracket and housing it was a breeze. Getting the unit back in the closet was a slight struggle, but it all worked out for the best got a chance to cleas behind the dryer, and the repaire was successful, phew.

My dryer was heating up very briefly blowing hot air initially then cool. I have a stacking washer/dryer set (2002). I initially turned off the gas valve at the wall, ran the dry for several minutes to clear the gas line, then unplugged the power. I was then able to pop the top using a flathead screw driver, securely prop it open, unhook the wiring harness to the front panel, unscrew the two front panel screws, and remove the entire front without having to unstack the units. From there, you remove the two screws holding the bracket over the coils (2 of them), remove the electrical connectors attached to both coils and replaced them with the new ones. I then replaced all brackets, screws, and such (you'll need to lift the drum when putting the front back on and make sure it is lined up), plugged it back into power and turned on the gas to test the unit which worked perfectly. The 62% of the time seems to be an accurate figure as nothing else had to be done to the unit. Pretty easy stuff...good luck.

we removed the top of the dryer which was clipped on. then removed the front, including the door, being careful to unhook the electrical elements. then we removed the screws that attached the dryer drum to the back of the shaft. then we took the shaft out of the bracket. then we removed the plate from the back of the dryer that held the ball, the bearing and the bracket together. then we waited for parts and thanked God that the weather was fair so we could hang our clean clothes out!!! the parts came ahead of the rain so it was reverse order. then try the dryer!!!fantastic!! to qoute my kids "you rock"

Taking off front of and top of dryer and panels on the back. Releasing the belt and taking out the tube un screwing the two pieces off the back of the machine putting new ones in and putting belt back around drum and setting drum in. Then holding drum while the front is put back on then attach top and a couple panels on the back.

removed top and front of machine. removed drum. replaced shaft, bearing bracket, and support bearing from inside. replaced grrounding ball and clip from outside. reassemble.
this should be available as a kit, and should include high temp grease to put in bearing bracket