DE7200AWW1 Frigidaire Dryer - Instructions

0) Turned off breaker at panel and disconnected power cord from 240v wall outlet
1) Removed screws that hold electrical cover plate on back of dryer.
2) Lifted the top of dryer using putty knife on 2 top edges of lid. This lifts up like a cars hood.
3) Removed the screws that attach the power cord to the terminal block and disconnected power cord
4) Removed screws that attach terminal block to dryer
5) Removed melted terminals by prying out of terminal block. Note metal lip on terminal has to be lifted in order to slide connector out. Also unscrewed ground wire from terminal block to dryer.
6) Drew diagram of what color wires go to what terminals
7) Cut terminals off of wires and connected new terminals. Crimped closed and used butane solder torch to solder connection between terminal and wire
8) Reconnected terminals to terminal block by sliding in. **Note, had to file down the edges of the terminals using moto-tool to make it fit as they are connected together using break-away tabs that leave a large piece of metal connected not allowing to fit in terminal block
9) Reconnected terminal block to dryer and reconnected ground wire.
10) Reconnected power cord to terminal block with screws
11) Replaced cover over wiring terminal block
12) Reconnected power cored to 240ac wall outlet
13) Turned breaker back on

UNPLUGGED DRYER.
1. I used a putty knife to pop the clips in the front. This allows the top to open like a car hood.

2. There are two screws one on each side holding the front to the body. Then there are clips which can just be pulled.

3. There are some electrical connections. I made a diagram and disconnected them.

4. The front slides up off two tabs at the bottom.

5. Peel and scrape off old felt. install new felt using high temp glue and clamps. The top one the plastic guides go to the top.

6. The belt has a tensioner on the bottom right and comes off easily.

7. There are three screws in the middle of the back of the drum. They were very tight and require a good phillips head screw driver.

8. Drum lifts out the front.

9. Unscrew the ball bearing assembly from the back, put the high temp lubricant on the ball.

10. Re-assemble in opposite steps.

Plug in and test.

First of all, the folks at Part Select have been terrific. I balled up my address and they were great in correcting my error and getting the parts promptly to me. They provide directions with the parts. And You Tube, is a wealth of information too. The process is to remove the drum and replace the nylon busihing that supports the drum at the back of the machine. Getting it out was no sweat. Getting the drum back in was a bit more challenging single handed. If I was going to make any suggestion it would be this is a good project for two sets of hands with the second set needed for about ten minutes. The You Tube video I watched said putting the front cover with the drum attached to the back of the unit would be the challenge and they were right. Otherwise, super easy and the results are it's back to "new" condition. Thanks again to Part Select!

Make sure you order a new belt and a new drum glide with the rear drum bearing assembly. If your bearing is worn out, so are the belt and drum glide!

1) Use a flat screw driver or putty knife to release the blind clips that hold the front side of the top of the dryer cabinet down
2) Swing dryer top up and remove two screws that hold the face of the cabinet.
3) Unplug the wiring harness and remove the cabinet face.
4) Remove the 3 screws that hold the drum to the bearing assembly (accessed from inside the drum. This makes it easier to remove the drum as the bearing assembly can be difficult to remove before you see how it snaps together
5) Reach under the drum and take the belt off the motor pulley, then remove the drum
6) Remove the old bearing assembly from the socket (slide up then out)
7) Remove the two screws that hold the bearing socket to the dryer
8) Fasten the new socket to the dryer (you'll need help doing this unless you have REALLY long arms because you have to reach inside the driver and the back of the dryer at the same time)
9) Grease the socket with the supplied high temp grease
10) Bolt the new bearing assembly to the drum and put the new belt around the drum
11) Put the drum back in and snap the bearing socket in and down
12) Guide the new belt around the motor pulley & tensioner
13) Glue the new drum glide / felt piece to the front cabinet
14) Put the cabinet back together

Removed 2 screws and replaced part--very easy.
I was very happy to find this part for a 1988 dryer

Unscrewed old frame, removed it and put in the new one. Now I have a brand new dryer. Thanks!

Took off front panel, removed drum and replaced parts listed. A bit tricky to keep small parts in place. However, masking tape helped. Best of all was the online diagram of how the parts were assembled. In addition, taking step by step phone pixs aided in replacing parts since there was some down time between diagnosis and installation.

While changing power cable from 3 prong to 4 prong connection on a recently purchased used dryer I found the terminal block partially melted due to improper connectors which overheated. The bracket and cover were also missing which presented a shock hazard for anyone touching the exposed connections and there was no way to connect the strain relief. I disconnected the old 3 prong cable, removed the old terminal block, installed the new terminal block (required opening the dryer top for access), threaded power cable through bracket and fastened with strain relief leaving loose, attached the neutral/ground wires to middle terminal connection point, red to red wire in terminal block and black to black wire also in terminal block and tightened bracket and added cover.

I removed the gate in the back and found the belt had snapped. I continued to dismanlte the entire dryer to see what else was damaged. I pulled the drum out and ran the unit to make sure the motor didn't burn out and that the heater coil worked, which both did (I had no idea, this unit came with the house I purchased. They told me is was broken.) So after finding the belt broken I saw that the top felt guide was rubbed down so far that the plastic guides where in paper thin, craked pieces.

I used the manuel that came with the felt guide to glue the new one on. If you do not replace the lower felt guide as well, make sure you mash the top felt down so that it's level with the lower felt. after I got my unit assembled the top guide pulled away because I didn't do this.
Installing the belt is timely, but easy. remove the drum then lay the belt around the visible line that the old one creates. Use this site's diagram to affix it to the pull and motor and that's that. Rotate the drum with your hand to even the belt out all around the drum to prevent it wobbling. I did this installation by myself, but it would have been much much easier if I had a set of hands on the other side of the unit.
Parts all fit together by either sheet screws or clips. Just keep track of which screw goes where. some are different sizes.

Used nut driver to remove screw and cover from dryer cord terminal block, used screw driver to remove two screws securing old terminal block, cut dammaged wire and stripped wire back and crimped on new terminal connecter, replaced old terminal block with new one, replaced two screws, installed new cord, and replaced cover plate and screw.

Dryer door would not close, part had broke and fallen in. Once part was received it took less than an minute to put the new one in and I was back in business.

thanks for making it easy to find the part needed. and the delivery was fast!

bonnie J.

Based on all of the other posts, their explanations were right on, so I won't repeat it here. You could probably do this repair on your own, but it helps having someone to hold the drum while reattaching the screws. I replace the rear drum bearing assembly and the belt. I would recommend replacing the belt. I almost didn't, but I'm glad I did. Once I had it off, I could see the cracks in it.

When installing the new bearing, make sure that you pack it with the supplied grease. Be liberal with it. I used what left over grease I had to grease the idler puller bearings too.

The dryer works perfectly now, with no squealing. My experience with Parts Select was flawless. The shipping was extremely fast, and the parts were as described. Finding the correct parts was a snap thanks to their easy to use web site.

Rear plastic drum support bearing got worn making the shaft come in contact with the metal bearing bracket. That contact created a groove overtime and eventually snapped the shaft tip off.

Cut power off. Remove all the screws from the front panel. (where the controls are) working from the bottom to the top. Insert putty knife between the dryer and the control panel and push down to release. Carefully disconnect the wire harness.
You will find 2 screws at the bottom and 4 on top holding the dryer door. Remove and expose the drum.
Remove the drive belt
Remove the drum.
You need a 5/16 nut drive to remove the bearing bracket and an extra set of hands to hold the support from the back.
Re-install the parts. I used bearing grease to make it run smoother
Attach the new shaft to the drum and reinstall the drum (its best done with help)

Re install everything back again. And you are done

only needed to attach knob with one hand.

After the part arrived, I located a pair of needle nose pliers. Then removed the broken one and inserted the new one. It was very easy.
I also noted that the new part was of a better design than the original. It should not need further attention.