FDE7976FW0 Frigidaire Dryer - Instructions

Unpluged the dryer, took out the light assembly, unpluged the wires to the unit, replaced the old unit with new unit from Partselect.
Plugged dryer in, problem fixed.
Taa Daa

Thanks, PARTSELECT.

That saved me about $50.00 YAHOO!!

1. Released the front latches under the dryer top and flipped it up.
2. Removed two screws holding the dryer front in place and flipped it down.
3. Tore off old drum glide and lower seal.
4. removed most of the remaining fuzz with sandpaper.
5. Glued the new seals in place.
6. Put everything back together.

All in all, about 30 minutes of effort. I managed to come away with only minor cuts and scrapes.

Much cheaper than a new dryer!

followed video and replaced part( cleaned and vacuumed dryer while I had it apart),relatively easy repair

my motor was making noise i tried to replace the motor but could not get the blower wheel off the motor so i had to buy a blower and housing assy. also... now it works great...

Motor replacement requires removing/releasing the top and front of the dryer, then removing the drum through the front of the dryer. The top is hinged at the rear and the front can be pried up. The front is held by two sheet metal screws that are accessible once the top is lifted up. Three screws hold the drum to the bearing at the rear of the drum. A small access door on the rear panel allows removal of the idler arm and its spring. You will need a socket drive with a short extension to remove the fan assembly from the motor at the front of the dryer, and it has a LEFT-HAND thread. The most difficult part of the replacement, once you figure out how to access everything, is getting the drum re-attached to the bearing at the rear of the drum. It can be hard to align the three screws, and once you have that done they need to be carefully tightened a few times after rotating the drum a few cycles, to get all the play out. Once the motor was replaced the dryer works like new.

Dryer door would not close, part had broke and fallen in. Once part was received it took less than an minute to put the new one in and I was back in business.

thanks for making it easy to find the part needed. and the delivery was fast!

bonnie J.

unplug dryer. lift the top of the dryer up and back. Take the screws out holding the front panel on. One on each side. Disconnect wires from door open stop switch and take front panel off. Remove drive belt from around pulleys and lift drum up and forward out the front of the dryer. I had to replace the plastic and metal holder and the grounding ball also. Remove the shaft from the drum and put he new one on. Put the drum back in, wrap the belt around the drum and set drum in plastic holder. Then just reverse your steps. Fairly easy.

1. I disconnected power cord
2. I used putty knife to loosen top by pressing into
the front spring clips holding it down and lifted the
front of the lid up against the back hinges and leaned
it back against a wall at the back of the machine.
3. Then I unscrewed the two screws at the top of the
inside of the front panel edges and unclipped the
wires from the door switch and then crimped the
metal clips holding the front panel to the main
body sides and then leaned the top of the front panel
toward the front and lifted it out and put it aside.
4. I then went to the back of the machine and undid the
two screws holding the motor area access panel and
took it off and put it aside. I then released the drum
belt tensioner and moved the belt away from the motor
pulley.
5. Then I removed the drum by lifting up on it so that the
ball axle could be pulled outward and then proceeded to
take the belt off and work the drum out of the front
panel opening and put it aside.
6. Once the drum was removed one could see the heating coil
assembly attached to the inside back of the dryer. One
needs to take off the two wires attached to the coil
spade connectors that are located at the ceramic
insulator. I decided to take out the whole assembly by
undoing the four screws at the outside back of the dryer.
7. Once the assembly is out of the dryer, then it becomes
necessary to remove the spade terminals from the
ceramic insulator, One must unbend the metal flanges
that have been bent at the base of the spade coneetors
at the surface of the insulator and then pull out the
spade connectors. Once this is done, then one can
unconnect the coil from the ceramic insulators holding it
to the assembly. Once the coil is disconnected one can
put in the new coil into the ceramic insulators, insert
the spade connedtors into the insulator, bend the
flanges to retain it and then reverse the disassembly
sequence for the assembly to complete the job.
Outcome,(I saved the old coil in case I need it in the
future.)
Outcome

Used nut driver to remove screw and cover from dryer cord terminal block, used screw driver to remove two screws securing old terminal block, cut dammaged wire and stripped wire back and crimped on new terminal connecter, replaced old terminal block with new one, replaced two screws, installed new cord, and replaced cover plate and screw.

Rear plastic drum support bearing got worn making the shaft come in contact with the metal bearing bracket. That contact created a groove overtime and eventually snapped the shaft tip off.

Cut power off. Remove all the screws from the front panel. (where the controls are) working from the bottom to the top. Insert putty knife between the dryer and the control panel and push down to release. Carefully disconnect the wire harness.
You will find 2 screws at the bottom and 4 on top holding the dryer door. Remove and expose the drum.
Remove the drive belt
Remove the drum.
You need a 5/16 nut drive to remove the bearing bracket and an extra set of hands to hold the support from the back.
Re-install the parts. I used bearing grease to make it run smoother
Attach the new shaft to the drum and reinstall the drum (its best done with help)

Re install everything back again. And you are done

Basically, i followed instructions on 1 video i seen, but was able to shorten repair by not removing drum, and was still able to access the thermal limiter switch to remove old one and install new one. Worked like a charm. Thanks Dan

After the part arrived, I located a pair of needle nose pliers. Then removed the broken one and inserted the new one. It was very easy.
I also noted that the new part was of a better design than the original. It should not need further attention.

only needed to attach knob with one hand.

I noticed for sometime that my dryer had been sqeeking...but I had thought nothing of it. It got alot louder as time went on and then one day the drum stopped spinning. Not to mention I had my son's 5th birthday party in 3 days. So I went online and found parts select. They sent me the whole assembly and I got it the day before the birthday, and it only took me 30 mins to replace it. Thank you, Parts Select for the prompt response and saving me for the embarrasment of having clothes all over the floor.

The repair went very smoothly. I'm a woman in my mid 20's and was prepared to buy a new dryer but I saw the part online for a very reasonable price and the video instructions were extremely helpful. I was able to fix the dryer quickly and cost effectively AND the part arrived in only 2 days! It all worked out very well.