GLGQ2170KE0 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Balsam Lake, WI
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dryer wouldn't heat
Removed the panel between the dryer and washer. The gas valve was right in front. The wires were in a plug and easy to remove from old part. The solinoid held in place by a clamp with two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PETER from Fremont, CA
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
No reheat
Pried the lid up and flipped it back then disconnected the front panel wiring harness and then popped the front panel loose at the top and dropped it down. Disconnected the ignition coils, removed the coil retainer bracket and replaced the coils. Reassembled it in reverse order, performed functional test. Success!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bret from Tampa, FL
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I shut the door too hard, and the old latch fell down into the inside of the dryer.
The new latch easily snapped it into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon Henry from Seabrook, TX
- Parts Used:
- 134472202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handle top mounting bracket on dryer door busted
Very easy fix. Removed remaining bottom mounting screw and removed old door handle. Positioned new handle on dryer making sure it fit properly in it's slots and installed screws into mounting brackets. Worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Mayfield, KY
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no problem
put door catch in hole
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mollie from Williamsburg, VA
- Parts Used:
- 134472202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handle broken on front load dryer
Simply removed the old broken handle screws and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from San Angelo, TX
- Parts Used:
- 134472202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer Handle Broken
Washer handle fixed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Brooklyn, NY
- Parts Used:
- 5303931775
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
no heat
Remove top cover 2 screws then remove front panel 6 screws remove wire connecter on the door panel. ignition coil is on the bottom left side need a short hand srew driver remove 2 screws remove plate holding coils remove coils and connecter. Reinstall in reverse installation. Dryer still didnt heat up so back to the drawing board :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bert from Silver City, NM
- Parts Used:
- 137539200
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
The Heating System Of The Propane Dryer Stopped Working
When I direct the dryer exhaust into the room during the winter there is an external lint filter in the ducting. For some reason,enough lint got by the dryers filter and over a few cycles clogged the exhaust. I correctly assumed that the dryer overheated and some thermal limiter had opened up. The manual had exploded views and I located the limiter. Getting to it was another issue. The manual gave nbo instructions on getting to the limiter, but I had installed a propane conversion kit when I first got the dryer. It was necessary to remove the top, control panel, and front panel/door assembly. Disconnecting the gas line,some cable connectors, and a few screws allowed the removale of the burner assembly, then removal of the metal tube that surrounded the burner assembly and held a number of sensors, including the thermal limit, which, as expected, showed an open circuit. The replacement part was ordered and checked out as a closed circuit, which it should. Reassembly was the reverse. A little difficult to work in the cramped lower corner of the dryer. I'm 82 years old now but machines cannot beat me!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Irvine, CA
- Parts Used:
- 137539200
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Error code 66 - door open
Remove 2 screws at the upper rear attached to the top panel. Slide panel rear back and remove. Remove 2 screws attached to the front control panel. Lift panel upward. Remove 4 screws attached to the front panel (2 at the top, under the control panel, two at the very bottom). Lift front panel up and off, and unplug connector to door switch. Remove some more screws on the internal front panel edges, and the front to back brace holding up the control board. Lift panel up and out, and remove the drum, too. Thermal limiter located toward the rear, attached to the heating vent tube. Disconnect and replace. Re-assemble in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from South Dartmouth, MA
- Parts Used:
- 134472202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken handle
EASiER than pie! Took off broken part, screwed on new part! Voila! Done. As good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Duluth, MN
- Parts Used:
- 134472202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I pulled half of the door handle off of my washing machine.
The new door handle was sent out the day I ordered it and arrived in three days! I unscrewed the old door and screwed in the new door (the new door handle didn't come with screws but the old screws were still perfectly good to use). My husband was impressed when he arrived home from his business trip!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Chicago, IL
- Parts Used:
- 134472202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cracked door handle
When new handle arrived, it took less than 2 minutes to replace the broken handle, using the original screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Plattsburgh, NY
- Parts Used:
- 134472202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken holder for dryer door screw
replaced door handle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Houma, LA
- Parts Used:
- 134472202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door handle broke
removed two screws and installed new handle
Was this instruction helpful to you?
Thank you for voting!