GLGR1042FS1 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara J. from Lancaster, CA
- Parts Used:
- 131450300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint filter was wearing out.
Just replaced the new lint filter with the old lint filter. The part fit perfectly. I did not have a problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DENISE K from cleveland, OH
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old knob was strip
remove old knob and washer that was on it put new knob on and turn the knob dryer was save
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from EL PASO, TX
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
knob replacement...
watched you tube video... a breeze
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Beverly Hills, FL
- Parts Used:
- 134844410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced knob, perfect fit and match
just pushed new knob on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TJ from SCOTT DEPOT, WV
- Parts Used:
- 131658800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door catch broken
Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Mentor, OH
- Parts Used:
- 131644700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door handle broke and came off.
Simply popped it back into place, careful not to break the new handle.
Was this instruction helpful to you?
Thank you for voting!
2 of the dryers knobs had broken off
I ordered the knobs at less than half the price I paid before from the retailer. The knobs came in the mail very quickly. I took the knobs from the package and put them on. Easy repair, and I was especially happy with the ease of ordering and quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from little Egg Harbour, NJ
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Lound noise inside dryer
1. unplug the dryer, remove the aluminum vent and move it to an area that has a lot of elbow room.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from SAN FRANCISCO, CA
- Parts Used:
- 5308027429
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Noisy squeaky dryer
Main problem was the bearing, replaced the belt and felt seal as well
The video instruction was very helpful
Was easy with basic mechanical aptitude
Dryer running great now
All parts from Partselect.com
Have ordered from them before and would order from them again
The video instruction was very helpful
Was easy with basic mechanical aptitude
Dryer running great now
All parts from Partselect.com
Have ordered from them before and would order from them again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SHARON from SUMMERVILLE, SC
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set, Wrench set
Dryer making horrible squeaking sound when running
I am a "do-it-yourselfer" despite my husbands opposition. I followed instructions from one of the posts on the site and took apart the dryer. I found the location of the rear bearing and took it out and replaced it with the new one. Easy as that. Made sure the parts looked the same. Made sure I saw how everything went together. I used a magnet to hold the ball bearing in place on the rear mount and taped the metal bracket on the outside of the dryer. Screwed it right in. Reassembled in reverse and works like a charm. To all the women out there who don't think they can do this. It's easy. Give it a try.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from PORTAL, GA
- Parts Used:
- 131658800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Our door catch got lost inside the dryer after the door was slammed to hard
I took the new door catch out of the packaging and just snapped it in place it was easy peasy and took less time than opening the package
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from dallas, TX
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Latch on dryer no longer worked
So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Valerie from Moultonboro, NH
- Parts Used:
- 134886700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
temperature knob was broken
Just fix it in the groove and pushed it on and it was done in seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NICOLE from KINGWOOD, WV
- Parts Used:
- 134886700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dryer knob cracked
put the new knob on
Was this instruction helpful to you?
Thank you for voting!