Models > FRE5714KW0 > Instructions

FRE5714KW0 Frigidaire Dryer - Instructions

Jump to:

All Instructions for the FRE5714KW0
106 - 120 of 529
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Blanche from Mansfield, PA
Parts Used:
134844410
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken selector knob
Just pushed it on. The gray on the knob is a little lighter shade than the original, but not a problem.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robin from Sewaren, NJ
Parts Used:
5303937183, 137513300
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Black lines and small tears
Previous comments on line were so helpful.

My husband and son took the dryer apart by removing the top in order to get to the drum. Part of silver rim that the Drum Glide is attached to was broken,it had been cut somehow. They had to soder it back in place so they could attach the Drum Glide and so far it's working.

Felt- I just ordered one with the adhesive and removed the damaged section used a wire brush, applied the adhesive ( which was more than enough) waited a few minutes for the adhesive to set, applied the felt, attached binder clips to hold it in place while working on the Drum Glide. Really easy.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
brad from oklahoma city, OK
Parts Used:
131553900
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Heating Element broke
much as described earler,
1. Removed 2 screws on back at the top and 2 on the chrome vent to access the belt and pulley.
2. Disconnected spring from pulley assembly and removed belt from pulley and motor.
3. Removed top of dryer.
4. Removed control panel.
5. Removed screws from inside dryer tumbler (all of them)
6. Removed bottom kick plate.
7. Removed 2 screws from inside panel (near tumbler) and 2 screws from bottom of front panel. Removed front panel.
8. Removed tumbler housing.
9. Removed heating element cover.
10. Removed heating element pan. (wires first)
11. Removed "bearing" by lifing it up (snaps in)
12. Cleaned and regreased "bearing"
Assembled in reverse order.
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Justin from lawrenceville, GA
Parts Used:
131553900
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
My dryer wasn't drying due to a blown heating coil
When it comes to repairs the only thing that I can fix are sandwiches. To say that I am a handy man is usually followed by snickers from my wife and friends... However, I was able to completley take apart my dryer, replace the heating pan and coils, put it back together and it works all by myself (my wife was standing behind me with a fire estinguisher when I plugged it in for the 1st time). I took the advice of some of the post I saw on this sight and took some before shots with my camera phone and marked the wires with tape so I knew where to return them and was able to get it all done. I was suprised at how easy it was to do and how simple a dryer really is on the inside. Ordering the part and doing it myself saved me a couple of hundred dollars easy.... this was the way to go!
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lorena from Fontana, CA
Parts Used:
134886700
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
worn down dryer knob
Just fit right in.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Iris from Saint Joseph, IL
Parts Used:
134844410
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Broken Knob, knob would slip, on/off knob
Removed old knob and tension band from shaft. Pushed new knob into place
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
robert from lake worth, FL
Parts Used:
137513300
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
clothes were getting stuck
after numerous holes put in my families clothes i looked on line and found "partselect.com". i ordered the front drum glide after seeing a similar story about the clothes being torn and getting caught and my family and i have our new dryer back!! yeah :<)
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Alan from Emporia, KS
Parts Used:
137513300
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Front drum guidesnubber ring was worn out
removed the top of dryer, pulled front panel back from drum and installed snubber(Front Drum guide).
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Pam from Borden, IN
Parts Used:
131553900
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Dryer stopped heating.
Called a repair co. Said it would be about a week before he came to the rural area my mom lives and he probably wouldn't have the part. He would order it after he determined the problem. So I went to your web site and ordered the item it said was 80% and two other parts just in case. He came and used the Heating Element Assembly and said it was a good thing we had it. He would have had to order it and come back probably a week later. THANK YOU!! WE needed the dryer repaired sooner and saved another service call. I am returning the other parts not used and you make it so easy to do. I plan on using your site again.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ann from WALLA WALLA, WA
Parts Used:
3204267
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
lack of heat
Remove top lid by pushing tab on either side with a putty knife. Disconnect the 2 wire carriages on right. Remove one
phillips head screw on each side that holds front panel to dryer body. Remove front panel by using flat head screwdriver to pry panel from body. Remove thermostat located on bottom right attached to front of motor on a plastic body by removing two phillips head screws. Disconnect wires and place on new part.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from ROUND TOP, NY
Parts Used:
3204267
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
The thermostat had deteriorated and no heat
Had to loosen drum and move it forward to get at switch. Didn’t have to remove belt.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from HGHLNDS RANCH, CO
Parts Used:
131553900
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
dryer heat did not work
The how to video was great. I had a little problem with getting the belt back on the pulleys. Not enough room for my hands. I did manage to get it back on ,and runs great
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dave from SAN FRANCISCO, CA
Parts Used:
5308027429
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Noisy squeaky dryer
Main problem was the bearing, replaced the belt and felt seal as well
The video instruction was very helpful
Was easy with basic mechanical aptitude
Dryer running great now
All parts from Partselect.com
Have ordered from them before and would order from them again
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steve from COVINGTON, KY
Parts Used:
134120900
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Dryer not heating
UNPLUG DRYER (this is key) Removed the top of dryer. used screwdriver and pliers to remove two screws and electrical connections then reinstalled new part stick the magnet behind the part to the back of the dryer to help control the small screws.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JEREMY from JONESBORO, GA
Parts Used:
134886700, 134844410
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Broken Timer Knob, Broken Start Knob, Possibly Damaged Start Switch
First, removed the metal access panel by removing screws. (EASY)
Second, pressed the timer knob onto the timer shaft. (EASY)
Third, mounted the start switch to the mounting surface. (A BIT DIFFICULT)

Fourth, pressed the start knob onto the freshly mounted start switch. (EASY)

Fifth, replaced the metal access panel by replacing screws. (EASY)

Dryer now functions like new.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the FRE5714KW0
106 - 120 of 529